Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Although there are some posts dealing with bond manager issues, I have not been able to find a similar issue. I am using part of the BLE code from nRFready Desktop 2 v1.0...
Hi,
i have some trouble with acting with the nrf 51822 ADCs. My Problem is that i have an Impuls which is 100 uS long and i have to measure it with 2 ADCs. I know that...
Hi,
What will happen when we press the service discovery button in the master control panel? do we get any event like BLE_GAP_EVT_CONNECTED? I couldn't find any detail regarding...
I'm looking for information to start developing BLE slaves with nRF51822, but I can't find any datasheets/SDK. Do I need to buy the Development Kit in order to have that?...
I have an issue with my keyboard working with the windows suface (on windows 8.1). Occasionally, the last character sent is repeated several times instead of one. I do not...
On the nRF51822, I see that by programming the readback protect register, one can prevent reading code regions 0 and 1 from the SWD interface. However, if one had access to...
Hi,
I just watched a webinar from the bluetooth SIG on how to create source code from the nRFgo Studio for the nRF8001. Is the same possible for the nRF51822? To create...
Hi,
We modified the ble_app_hrs code to work with accelerometer peripheral, and we have created some custom characteristics with custom uuid's. Now we need to set the device...
Hello, Everyone:)
Nice to meet you !
Please could you commennt my first question on this community zone.
I've a question for the accuracy of synthesized clodk 32k on...
Hi
i am using NRf51822 custom board. In that i have NOR(spi0) and LED(i2c0).
But switching from spi0 to i2c0 is not possible so that i am not able to switch
off led...
Hello,
I'm using nRF51822 to implement a proprietary radio protocol. My first attempt, in the receiver, was polling the EVENTS_* registers. An example:
NRF_RADIO-...
I was trying to get access to the app_uart library, so I included app_uart.c in the "Source" folder; then added \Include\app_common and \Include\ble\softdevice in order to...
Hi,
We are using nrf51822 custom board.
i want to hard reboot of my device whenever gpio button is pressed for longer than 10 seconds.
i am using ble_app_hrs application...
from the product spec
NOTE: The 3 bit pipe information in the STATUS register is updated during the IRQ pin high to low
transition. The pipe information is unreliable if...
