after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I try to use CPSMS command to reduce the power consumption. The idea is to send a MQTT message every 10min and have the GPS coordinate every 5 min.
The NRF9160 is...
Hello,
I have 3 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to stream left/right audios and I'm able to achieve it.
https://developer...
Hi,
I am investigating low power modes in the nRF9160. I am currently using the GNSS sample code and getting around 36mA. Is there any way to configure the base code to...
Hello,
I have implemented an application for nRF5340 chip derived from the Zephyr AWS IoT MQTT sample. The application is based on W5500 Ethernet driver so the idea is to...
Hi,
I’m trying to have two nrf9161s exchange data back and forth as quickly as possible. Initially the first radio is transmitting, and the other is receiving (3 sub-slots...
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. My app configures as BLE Peripheral. Now I want to keep track of the device names of connected...
Hi,
Sorry for the very basic questions. I am new to nRF connect SDK.
I want to develop a ble custom central application with my custom characteristics. I started to look...
Hello!
I have an application using MCUboot and a single application slot. I want to use the Retention System to signal to MCUboot wether to boot normally or into serial...
Hi,
I want to know how to use extended broadcasting in nRF5SDK.
I have tested the Broadcast Multiple of NCS2.6. The maximum extended advertising data length is 31 to 1651...
Hi! I am beginning development on my first BLE project using nRF Connect SDK in VSCode. I have done a few projects using the old nRF5 SDK. I am wondering what is the best...
Using VS Code, I've tried to build the "BLE UART service" (= peripheral_uart) for the nrf52840dk_nrf52840 board. According to the documentation, this board is supposed to...
I am working on a project that uses nRF5340.
We are now looking into designing software update mechanism. As a part of this, on the app core I am planning to move slot1_partition...
Hello,
I am implementing firmware to communicate using UDP between two nRF7002.
The sender does not know the IP address, so it tries to know the IP address of the receiver...
Hello,
I'm having an error when running the spi_flash example on a nrf5340DK.
I added this to the .conf file to have more info:
Here are the console logs:
I'm...
