after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am new to nRF MCU's and nRF connect SDK, I want to interface my INMP441 (I2S MIC) with my nRF52840 MCU to print the mic data on serial monitor , can anyone please link me...
Hello, I am working on a project for nRF9160 that is supposed to provide FOTA/DFU functionality for main application, modem and nRF52832 co-processor acting as SPI HCI slave...
Hi Nordic Team,
I am currently working on developing applications for custom boards using the nRF Connect SDK v2.6.0, specifically focusing on the nRF52840 microcontroller...
I have build a simple program to Interface my PDM (ICS 41351) Mic with my nRF52840 DK usnig nRF SDK on VS Code, although the program in build and flashed successfully I cant...
Hello Nordic Team!
I updated to version 5.0.0 of NRF Connect for Desktop and since then, when I try to program my development kit in VS Code, it can appear as connected...
Hello,
I wanted to evaluate the nRF53 platform with nrf connect SDK so I got new nRF7002DK board. I have following versions of all tools installed.
- nRF connect SDK ...
I want to edit the sample source (nRF5340 Audio) and program it on my own board. The connection is CIS. I am using NCS version 2.5.0.
I want to set the I2S clock as follows...
I tried the following settings to output 12.288MHz I2S MCLK with nRF5340 Audio, but it did not work as expected.
The I2S settings I want to output are as follows.
MCLK...
I am currently writing sniffer firmware to the nRF52840 and am trying to check Thread communication using WireShark.
When I displayed the RSS, I got the value shown in the...
Hi,
I am just starting to develop a nRF5340 based prototype. I am using the openthread CLI example as the first step. I have configured the device tree to suit our board...
Hello. We recently started working with the new nrf connect sdk and we need to implement a very simple bootloader that would only jump to the main application at a specific...
Hi there,
I have a project developed in SES, using nRF5 SDK v15.3.0 with only Just Works security without using LESC running on nRF52840. It has been running fine for 2...
In our custom board we checked WIFI, facing below issues, 1. We flashed sta sample project to our custom board facing the issue below. Is there any configuration needed to...
I am using Asynchronous API of uart to receive the data. During the reception I face UART_ERROR_FRAMING issue in UART_RX_STOP event. But after getting that too it enables...
