after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I was facing some buffer issues while setting up I2S, so I decided to flash and test out the i2s echo sample provided in the sample programs in the SDK. I changed the DT_NODELABEL...
I wanted to get FOTA running on a PineTime devkit board (nrf52832) just to test and see if it works, but am getting the following error message:
/opt/nordic/ncs/toolchains...
Hello
We have developed a device based on the nRF9160, one of our potential clients asks us if the device has High Priority Access, he says that this information should...
Hello!
im trying to write chunks of bytes to an sd card in a non blocking style. One possibility im pursuing is to use SPIM, where the actual writing is done by DMA-Controller...
Hello again,
I am putting together a device that need a lot of local non-volatile data and uses a lot of flash on my NRF52833. I am running NRF Connect SDK 2.6.0. I'd like...
Hi there,
I'm encountering an issue while attempting to establish an Internet connection on my Linux machine using the nrf9160 DK SLM (2.6.1) application. I've flashed the...
Attempting to get up and running with the basic zephyr lvgl demo found in `zephyr/samples/subsys/display/lvgl`. Text appearing on the screen is of poor quality but still legible...
Hello,
We are currently developing a WiFi library and just started on implementing HTTPS and ran into some issues. Since we don't have enough flash and memory for using...
Hi everyone,
I’m currently working on setting up Azure communication using the latest SLM version for PPP (Point-to-Point Protocol) support. Here’s the configuration I’m...
We have a Waveshare display and a npm1300dk and I wanted to know the proper way to add the npm1300's config.overlay file, generated by nrfConnect's PowerUp, to the west command...
Hi,
I faced some issues regarding multiple IRQ_CONNECT being onvoked on the same irq and I went into this post :
LPUART nRF5340 fatal error - Nordic Q&A - Nordic DevZone...
Hello! I am using nRF Connect SDK 2.6.0v. I created a west workspace and i want to make custom board. I took reference from Devacademy nRF Connect SDK Intermediate Lesson3...
Hello Nordic
Use NRF52832 、 NCS 1.6 、“zephyr\samples\basic\blinky” sample.
In hardware, my board doesn't have a low-speed clock, and the reset pin is floating. Therefore...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
