after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I have a project that uses nRF5340 with MCUboot and multi image update configuration. The update works, but today I noticed that the pcd_sram RAM region seems to be...
Dear Support Team,
Hardware : nRF5340 Custom board
Software : nRF Connect SDK v2.2.0
I have implemented OTA FW update for nRF5340. I've used multi-image simultaneous...
Hello ,
i am trying to find out advertisement handler while SD advertising in SYSTEM ON mode.
i have added a simple counter to see if it is increasing or not but it is...
Hello fellow developers!
I am currently working on a scale application using the nRF52 DK, and I've run into a roadblock regarding the integration of the HX711 load cell...
Good morning,
I would like to know if I can work with Zephyr with C++ and how to do it.
development software, with versions:
Windows 11
nRF52840-DK PCA10056, 3...
Hello
I'm suing the smp_svr sample from the Zephyr SDK 2..6.1
I want to change the CONFIG_MCUBOOT_IMAGE_VERSION to force the OTA DFU ( over bluetooth ) but when I add...
Hello Nordic Team,
I am writing because I encountered an issue while developing a BLE application on the nRF5340 development board. Currently, I have set up this callback...
With multiple of the provided samples with the SDK, I'm getting a repeated build loop that ultimately fails due to a remaining "dirty build.ninja". This is primarily with...
Hi,
I am working BT840F which has nrf52840, I am using ble_app_uart example to transfer UART data to app. I wanted to know what is the system frequency of the microcontroller...
Hi,
I am using an external flash on the NRF52840DK via SPI and have established working communication with the flash memory. However, I need to disable CONFIG_SPI...
In my project, using nrf52840 controller, I am trying to store 253 bytes of data in NVM, but I encounter an error: "flash_nrf: invalid address: 0x00100ff8:8." Is there any...
Hello DevZone,
I'm porting my project from NCS 2.5.0 to NCS 2.7.0.
I know that there are lots of changes in build system, especially in Zephyr sysbuild. So, I decided...
Hello, I was able to update nRF Connect SDK to v2.7.0 fine using nRF Connect for Desktop. However, the nRF Connect for VS Code extension update v2024.7.13 causes VS Code launch...
