Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
Dear all and Nordic Staff:
I am learning about dynamic multiprotocols and found examples of dynamic multiprotocols for Thread and BLE in the "nRF5 SDK for Thread and Zigbee...
Due to the system design of our products, I am going to need to sideload any firmware update binaries. That is, my application code will handle receiving the update through...
Hi
I am using ncs v2.3.0, mesh chat example
I have used CONFIG_BT_CTLR_TX_PWR_PLUS_8 =y , and it works quiet well, now how can i implement CODED_PHY (long range) in this...
Hello,
I came across a Nordic Q&A discussing a sample called hci_uart_with_usb_uart_bridge in this post . I have searched in the v1.0.1 tag but couldn't find the mentioned...
Hello,
I'm attempting to establish communication between an nRF52840 and an nRF9160 on the nRF9160DK using LPUART. Initially, I tried using the interrupt-driven mode, but...
I get the registration "parse_cereg: LTE mode not found, error code: -22" error,when try to connect to LTE network in china shenzhen.the hardware is custom use nrf9160 chip...
sdk 2.1.0
nRF9160
Hi, I need to parse a JSON file and for that I'm trying to use zephyr's json.h library. Based on the automatic test file I built a piece of code for...
Hi,
I am trying to use an ST7789 display with the NRF9161DK, I was following this guide but got no luck:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b...
Hello,
I am trying to use a membrane keypad that has 5 buttons. It's not a matrix keyboard so I was just going to add 5 buttons into whatever gpio pins I can spare, but...
Hi,
I'm trying to use the samples/subsys/modbus/rtu_server/ sample. We use the st3485eb as rs485 driver. The problem is that I don't receive any data.
I'm converting our...
Hello DevZone,
I'm testing the nPM1300 with the battery inside the Thingy:52, which has rated capacity 1440mAh and rated voltage 3.7V.
The charge current is 800mA.
I...
Code that compiles just fine under V2.5.3 fails when using V2.6.1. It appears we have all the conditions met, not sure what we are missing.
warning: LOG_PRINTK (defined...
Dear all,
I am using nrf5340 audio dk to test the LE audio. I have already built and flashed the nrf5340_audio application to the device. But I cannot find the nrf5340 in...
I would like to create a project that my custom board of nRF52832 will communicate with Movesense device (which also is nRf52832) over BLE, to collect data from the sensors...
