Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have ncs version 2.6.0
i have two nrf5340 audio dks
i used nrf5340_audio dk sample.
Configured on dk as gateway that takes input fotm microphone used on the audio...
Hi,
I am using the PPKII in ammeter mode with an external battery to measure the currrent consumption. It would be really helpful for me if I could simultaneously measure...
Dear Professionals ,
I have series of questions to ask concerning the circuit configuration of the QFN73 And QFN48 for the NRF52840 as shown in the documentation site https...
Hi
My PPK2 was accidentally flashed by the nRFConnect's "Bluetooth Low Energy" app and then it bricked.
PPK2 then could not be detected by "Power Profiler", even "Programmer...
I have 2 nrf5340 devices, one running the Unicast Client and one running the Unicast Server. On the initial connection I am able to successfully stream audio.
On a restart...
I have been using the nRF7002 DK board; the nRF7002 uses the QSPI bus and the external NOR flash uses SPI.
The nRF WiFi driver's HAL and interface functions all require...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made:DFU procedure...
The nRF5340DK's are not programmable on my pc. I have no issues using nRF52DK and nRF52840DK. I have 3 different nRF5340DK's, they all have the same issue.
When I try nrfjprog...
Hi There,
We're new to Nordic and in the process of attempting to move our custom Xamarin application and boards over to use the nRF52832 and the nRF Connect SDK. Has anyone...
Hello,
I used two samples, application_update and SLM, to test and try updating the app from application_update to SLM. I first downloaded the firmware of application_update...
I would like to store context information for each connection, but with central and peripheral connections storing different information. Ideally, this is done in two separate...
hi support team,
we can see the slide in this link： /cfs-file/__key/communityserver-discussions-components-files/4/3201.Measuring_5F00_distance_5F00_with_5F00_Nordic_5F00_Distance_5F00_Toolbox_5F00_slides...
hello Nordic
we are working with nrf52832 and nrf52840 running with ncs v2.5.0 (waiting for v2.7.0 cause 2.6.0 have some issues with cmsis fft tables that prevent us from...
Hi
We are using STM32 board as a HOST controller and NRF9160 as cellular modem. On the STM32 board PPP client is running over serial interface.
We need PPP server support...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
