Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Is nRF Mesh app support feature that send customize data/command to node? The goal is to transmit data from phone to node, where it will be processed and used to trigger actions...
Hi
This is my first time using nRF connect and Visual studio but I have been following through first the Fundamentals course on the Dev Academy using the nRF52840 DK with...
Hi
I found some Bluetooth send the data unstable problem after i enable the usb cdc acm function. Can you help me to
check my setting that has missing or not thanks. ...
Hi,
I am adapting the Azure IoT example for use with the nRF5340DK and nRF7002EK.
The configuration is:
- sdk: nvs 2.6.0
- example Azure IoT hub
Initially, the getaddrinfo...
Hi Support Team
We test the nRF52840 power consumption of Thread Device follow the below links document.
(+) Analyzing power consumption in Thread Sleepy End Devices...
Hi,
I'm trying to increase the UART buffer size for the asynchronous UART API, but I'm encountering an error. When the message size is set to 255, I can successfully receive...
Hello all,
I config nRF52840 dongle P0.24 and P0.22 as GPIO_OUTPUT. But when I change their value, they are always 0.
I use the same way to change other pins such as P0...
Our product works fine. But I was wondering if we should be completely disabling the NRF_LOG functions for production builds. I suppose it could be using some power and processor...
I'm having a really frustrating time with a custom 7 segment display board I'm developing for scorekeeping. It seems to be successfully flashing using a Segger EDU mini, but...
Hi, I have a nRF52840 DK and I tried powering it with a USB cable. The issue is when I look into device manager the device is not showing up, and when I try connecting the...
Hello !
I'm struggling a bit with the USB HID boot protocol, I have a lot of stack overflow error when trying to do operations while in the get_report callback.
I know...
I'm embarking on a new project involving a sensor network of up to 3000 devices within a warehouse for industrial monitoring, and I'm considering an OpenThread network-based...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
