I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi there, I am trying to do a blocking simple ADC measurement in using NRFX drivers in a threaded context, however when I build I get the following error:
gen_isr_tables...
Hi,
I am using nRF9160DK v0.9.0 with Cellular Monitor 2.4.0, and I have flashed AssetTracker2 via the "Program device" button.
Although asset tracker works fine uploafing...
Hi,
Using the nrf Connect Programmamer v4.2.0, I get the following error when connecting to J-Link on some of my custom boards (about 30%):
When I run nrfjprog...
I am attempting to enter a sleep state (System Off) with a wakeup button . I set all of my GPIO pins to the default config except for my wake up, configure the appropriate...
Hi
I am unable to get the Guiconfg to work in lesson 1 exercise 2 of the nRF Connect SDK Intermediate course.
I have attached snap shots of the output when I try to run...
I'm using the custom board of nrf 5340 with 7002.
When I run the sample project of Hello World, the current is about 90 ma,
and I run the sample project of WI-FI Scan...
We are going into sleep mode for the processor. We are using Zephyr and sdk 2.3. We also are keeping a running count of seconds and synching that once a day with a modem....
Hello,
I'm working on a product using the nRF9160 and facing challenges with poor LTE signal strength, leading to significant power drain when the device goes offline. I...
I was pairing using nRF connect app via mobile phone and I noticed that there's a check mark which says "PIN contains letters or symbols":
Is there a pairing method which...
Dear,
I want to use the nPM1300 in my design for general Power Management.
I also want to use a Load Switch to disable some components in my design, but I do need to verify...
Hello,
I'm developing a firmware based on Zigbee CLI sample and enabled DFU of app core and net core via serial.
Now I am setting a custom key for image signing and...
Hi, i've been trying to use gnss function indoors and therefore i need to install an external antenna on my nrf9160dk.
I've read the requirements but i'd like some professional...
i need information on power consumption during advertising and connection in my case its taking too much high current around 1 ma in advertising and 1.5 ma during connection...
