Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello
I need the code where i can get mac addresses of all mesh connected devices. Suppose <- this is the link to find only one connected device. Is it possible this code...
Hi
After updating to latest nRF Connect for VS Code i have an issue debugging my project with Ozone using the "Debug with Ozone"
With previous version the generated jdebug...
We are having difficult getting a R&S CWM500 to connect to our nRF9160-based device (operating in CAT-M1 mode). We are using a R&S test UICC. We have already attempted all...
We tested our project a while ago with nrf sdk v1.9.1 using the lte_ble_gateway sample (app on nrf9160, hci_lpuart on nrf52840 using a nrf9160dk board). Now we have developed...
The documentation says ...
The sample displays the following output in the console from the non-secure firmware:
SPP: send message: Success
SPP: process signals...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0
IAR EW ARM 9.30
I'm trying to include...
Hello Team Nordic,
I am running a GNSS sample under SDK 1.9.0 and using modem firmware version 1.3.2.
I can get location without using A-GPS support but we get error...
The second instance of UARTE, UARTE1, was enabled in the configuration file. The receiving interrupt of UARTE1 failed to enter. Please help to check the reason
Hi everyone.
I am using nRF Connect SDK v1.6.1 (it's an old project) on a custom board with a nRF5340 on it.
The firmware is based on the central_bas sample project with...
Hi,
I am trying to create an ad-hoc network with several nrf5340 boards using 802154 radio, e.g. whenever each node transmits, others can receive the transmitted packets...
Hi,
I'm in the process of developing a new Matter device, using the Matter template as starting point.
When trying to commission the device it fails at step 8 (AttestationVerification...
Hello,
I am developing my own application using nRF Connect SDK with the nRF5340.
I want to drive multiple GPIO pins at the same time using the function gpio_port_set_masked...
Hi!
I am working on creating a Low Power mesh network and am trying to decide which communication protocol I should use with the NRF52840. There are no nodes in the network...
Hello,
I'm using NCS 2.0.1 on a nRF5340 board.
Currently I have some troubles with getting a response if I try to write a BLE characteristic from an iOS app. The write...
