after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have noticed that the function sd_rpc_open(...) of pc-ble-driver takes more than 1.5 seconds.
I have tried an example heart_rate_monitor which is supplied with pc-ble...
Hello,
I am using nRF52840 DK, and SDK version 17.1.0.
I want to dynamically control CLOCK source.
I tried to release( STOP ) HFCLK( XTAL ) source using nrf_drv_clock_hfclk_release...
Hi there
When the EVENTS_DEVMATCH is raised, this signals that the device address received in the radio data packet matches one of all enabled addresses in the BASE0/BASE1...
Hello,
we faced sometimes the issue that the reset reason Register RESETREAS is Zero at Startup. What does it tell me? So what happend in the Firmware that there is a reset...
I haven't been able to find any documentation or forum posts along the lines of the problem I'm having, so...
I'm trying to use an nRF52-DK with nRF Connect Desktop to connect...
Hi,
I'm using nRF52840 with NCS 1.8 on the existing ongoing development project.
Recently I implemented shell commands, to be used during testing procedure either via...
Hello
I have seen that using SDK 1.17 there is a possibility to set one channel that will be scan 37/38/39. I looked on SDK 2.2 documentation and I didn't seen this option...
Hi
We encountered speed issues with the download client library and CONFIG_DFU_TARGET. The problem can be reproduced using the download example. Without any changes I usually...
Hello,
Im working right now on a product which saves the update file (init + app packet) on its Flash in a specified memory section.
After "uploading" the file in the...
I have integrated MCUMGR to perform FOTA and it does successfully perform the updates where both slot0 and slot1 locations are from internal flash. As the code size is getting...
Hello !
I bought a new nRF51DK board and need to read its RAM data. I used nRF connect to erase it. The data read by nRF connect shows 262144 bytes and I don't know the...
Reproduce issue:
Windows 10 21H2
Set global git option gpg.format to ssh
git config --global gpg.format ssh
Install nRF Connect SDK v2.0.2 with Toolchain...
We are using the external flash w25q32jv via SPIM connection. the configuration as below.
arduino_spi : & spi3 {
status = "okay" ;
compatible = "nordic,nrf-spim" ;...
