Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm working with the ncs 1.6.1 peripheral_uart example and am looking to increase the size of the data frame to send 240 bytes per data frame.
I have seen several...
I am taking mqqt_simple of NRF9160 as reference for this question,
This is questing regarding, what is recommendation / Philosophy of using MQTT in NRF9160 with other codes...
Hi,
I'm programming a custom board based on Taiyo-Yuden EYSHSNZWZ module (with nRF52832).
I'm using the secure_bootloader example from SDK for OTA DFU, in order to flash...
I'm using the nRF-PPK2 to measure device power usage. I've noticed even at low sampling frequencies (>= 100Hz) it exhibits considerable lag at some point. Most annoyingly...
Hi Sir,
As we know the nRF5340 doesn't release the Circuit Board Guidelines (nAN-40) like nRF52840 yet.
If we need to design the nRF5340, could you share the recommended...
Hello,
I'm doing a comparison between MQTT on TCP and CoAP on UDP over NB-IoT and LTE-M. The communication to the cloud works as expected for both protocols. MQTT is used...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
We want to start with ble_app_uart example for our product but it the firmware halts at CRITICAL_REGION_EXIT() in nrf_sdh_enable_request.
We are using the example from 17...
Hiii, is there any libraries or example to read nfc tag through clrc663 nfc reader, could any one direct me to the any solution
thanx in advance
suprith
I am having problems setting up UART communication between nrf9160 and nrf52840 on Thingy91. My set up consist of a Thingy52 and a Thingy91. I am using ncs version 2.0.1....
Hi,
I've been working on Open Thread recently. I found that after I send provisioning request, even though there are 3 servers "enabled provisioning", the callback function...
Hi,
I am trying to setup a raspberry pi 0-W for flashing nrf devices. But nrfjprog doesn't seems to work.
I am using Raspberry Pi OS (32-bit).
I have fetched Segger...
Hello everyone,
I've got a simple question here today. I'm making use of the nRFCloud on our nRF9160-based system.
When using the different APIs to nRFCloud, be it location...
Hello team,
I am having a problem running LWm2m sample out of the box on Thingy91 (SDK 2.1.0, programmer 3.0.4). If I enable any of the sensors using something like the...
