Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
We are using ANNA-B112 module with nRF52832 chip and trying to store the product serial number in UICR. From the description of UICR, it seemed that the CUSTOMER area...
Hi,
A have an application on a custom board that will not start, unless I use JFlash Start Application command, or attache the debugger. I already added CONFIG_BOARD_ENABLE_DCDC...
Hi,
given "nrf_drv_twi_xfer" or its "nrfx_twim_xfer" younger brother is used to communicate over I2C, and its a TxTx tranfer, than what does "nrf_drv_flag_tx_no_stop"...
I am using bleak and python to connect to a ble device and then using subprocess to run the dfu. The ble device disconnects when the dfu starts and then I get "Connection...
I have a Thingy:91 board that appears to be broken, no response either on the LED or via USB UART when switching on.
I've earlier done some development with it, and hooked...
Hello,
I am attempting to follow along with the AWS IoT example. Everything has gone OK so far (Create a Thing, Create a Policy, Create and download certificates) until...
Hi All,
In our product we have noticed that, on a few occasions, some important information that is saved using FDS (in a file with ID: 0x02) are being erased when an OTA...
Hi,
Do you have a recommended circuit for supplying VDD_GPIO with the right timing relationship to VDD?
Section 11.1 of the datasheet says "VDD_GPIO should be applied...
Since the 9160 will vary his transmit power based on signal strength, is there any way of determining what power is being used for a given transmission? I know that the max...
The Edge Impulse firmware compiles and flashes to the Thingy53, without problem. I would like to increase the range of the BMI270 accelerometer, but can't find any reference...
I am using 52840 and SDK V14.2.0. When compiling nrf_ble_dfu.c I see the following error in nrf_dfu_types.h: line 258
"two or more data types in declaration specifiers....
Hello,
I am getting 0x07 error code when invoking sd_ble_gattc_char_values_read(..) function.
I am using SoftDevice 140 v6.1.1 APIs. I have an NRF52 dongle and I programmed...
Hello,
I am trying to send status messages to a Client model with a specific unicast address on one node. This node's parent element has both generic onoff server and client...
When i define macro
CONFIG_LOG =y
i want to use log
The program can not build successfully
FAILED: zephyr/zephyr_pre0.elf zephyr/zephyr_pre0.map cmd.exe /C "cd...
