Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear Team,
I am trying to use smp_bt_register and smp_bt_unregister calls in order to add/remove BLE SMP characteristic in real-time.
However, I keep getting 'undefined...
Hello,
I know that this issue comes up from time to time. I'm raising it again, because to my opinion there have to be a solution for this. Perhaps there is, that's the...
I am currently working with the Nordic nRF5340DK board using the official Matter light bulb example from the nRF Connect SDK version 3.1.0. I am also using the nordicconnectedhomeip...
We are designing a board around nRF54H20, and nPM1300, with some peripheral on VSYS, some on V3.0 BUCK2 and other are on V1.8 BUCK1. We also have detachable battery in place...
Hello,
Is the value readable by AT+CGSN the correct IMEI for the nRF9151?
Is there a way to read this value using JLink (nrfjprog)?
IC: nRF9151
SDK: NCS v2.9.2
Base...
Hello,
I received an email regarding the new course for nRF54 series parts and when I click on the link I am blocked by a Cloudfare generated web page. The Cloudfare ray...
Hi, We currently have a custom board with a nRF54L15 (final production silicon) paired up with a nRF21540 RF front-end module (FEM). This board is running Zephyr with v2.9...
Hello! I am using the nRF7002 in promiscuous mode to capture Wi-Fi traffic. Everything went smooth in AP mode where we use another nRF7002DK as a transmitter and our computer...
Hello,
We are entering preproduction build for a custom design using the nRF54L15. We need to know the solder ball dimensions and the recommended solder-mask dimensions...
Problem:
Reset reason logic works correctly when programming via SWD
After DFU programming, reset reasons are detected incorrectly
Even after unplugging/reconnecting...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
