Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
We have designed a product with NPM1100. With the NPM1100 set to output voltage of 3.0, we have measured the output across multiple devices to be in the 3.1 to 3...
Hello everyone , I am interfacing and trying to process GPS data received over UART port. The GPS outputs NMEA based sentences at a rate of 10 Hz. I started using the example...
I've tested two scenarios using a hardware loopback to test UART functionality. The double buffer approach does not work as expected.
SDK version 1.6.1
CONFIG_SERIAL=y...
Hi,
I used nRF91DK for almost 2 months non stop to debug the final nRF91 based board for our air quality monitoring hardware to fight the propagation of Covid virus.
But...
I tested various copy methods in terms of instruction cycles, that I determined with DWT.
For that I copied an uint8_t array size 70 by
for Loop --> 63 Cycles
memcpy...
Hello,
I am using nRF52840 dev kit with sdk 17.0.2, s140 softdevice and dfu bootloader also implemented.
When I download the firmware to dev kit it works as intended...
Hi,
i am working on nRF52832. i am facing a issue of RESET when i call advertise_start() again after advertise duration. in debug it shows fatal error.
Hi there,
I've installed and followed the nRF Connect SDK manual install getting started guide ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
I'm using 52832 as a Central(SDK_17.0.2/S132_7.0.2), and sometimes get a connect-disconnect failure with reason 0x3e.It happens randomly and frequently.
I search the forum...
Hi Supportteam,
i am trying to use Release Assistance Indication (RAI) to shorten the RRC-Connected using nRF9160 DK.
I'm enabling REL14FEAT with the following AT commands...
Hello, sir.
I used to work on twi0 and twi1, but now I'd want to shift both twim0 and twim1. However, I'm getting an error saying that 'NRFX TWIM1 INST IDX' is undeclared...
Is it possible for nRF Connect iOS app to display devices that were connected/paired through the iOS Settings menu? The problem I am having is when looking to perform DFU...
Hi iBasis support,
I'm having a billing issue with your website. I'm using the iBasis card with the NRF9160DK board.
When I ran out of data, I just follow the link on...
