after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am getting starting the nrf52832 board with an LSM6DSL sensor for motion recognition. it is possible in edge impulse ??
how to configure the firmware Development and how...
Hello.
I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
When making a BLE connection, you will receive an advertisement first. Then SCAN_REQ...
Hi Nordic,
I try to find an API to set the duplicate filter when scanning. But I found nothing.
I want to use the dulicapte filter disable feature to improve searching...
Hi. I've been working on getting a gsm modem functional using the GSM Modem Zephyr driver on an nRF5340. I believe I have the overlay file setup correctly, but am recieving...
Hi
I known that for NB IoT networks, a device can only be attached and separated 30 times in 1 hour. If the number exceeds the number of times, the modem will have to wait...
I'm using nrf_delay_ms in main on "ble_app_beacon", but the delay time is much longer than I set.
I have set 2000ms delay to log, but it seems 4s or longer than I set.
Hello,
I am able to get a successful confirmation that my application has been updated using the nordic secure bootloader over serial code example. However, my application...
I'd like to both use printf and NRF_LOG in my application. However, I have not been able to get both working simultaneously. Is this possible?
I init the logging like: ...
Hi,
Please help me deal with the problem that P0.26 IO port is invalid as a key
I connected the P0.26 port to GND and used SES simulation to see the following results...
Hello,
i have an issue with i2c on my nrf52840 dk. I attached the distance sensor vl53l1x to pin 27 (SCL) and 26 (SDA) and wanted to communicate via i2c with it. To test...
Hello
I have an application running which boots up fine.
I've written a bootloader which boots up first, and then jumps into the application including softdevice.
So...
I am trying to implement a TCP server with TLS support. I have the following confusion-
Do we need to use mbedTLS API explicitly or is it internally handled by a zephyr...
Hi,
I am developing a simple application where I read some data from a sensor, and publish the data with MQTT. I want to use PSM to conserve battery life, and I am able...
