I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
i want that my device shall advertise after i press a button for 5 seconds. there is a feature of long press for button kindly assist as how to use this for advertising
Hello,
I am currently trying to combine the NRF52840 (Development kit) with the Arduino Ethernet shield containing an W5500.
I was wondering if there is any example...
I have been trying to figure out how to use SPI on nRF Connect SDK. I cannot find a simple enough example to get started other than the convoluted SPI flash example or the...
We find a Beaocn from other distributor , it got very less fluctuations. RSSI table show below.
Test method: 10 RSSI were collected from a hand-held mobile phone at...
Typically the Base address registers and Prefix registers are used to configure up to 8 logical addresses and then RXADDRESSES is used to filter which of the 8 logical address...
Hi,
The new AT monitor have a hard-to-reproduce bug: the subscriber entry list alignment is not specified in the linker script. Since structs are always aligned, that means...
Hi,
im porting our nrf9160 application from SDK 1.3 to SDK V1.6.1. and facing error while accessing NVS device in SDK V1.6.1.
in SDK 1.3 i used "device_get_binding(DT_FLASH_DEV_NAME...
Hi,
I have have certain thread that I would like to be active during a ble connection. I can suspend it when not needed and resume when connected. But as long as the thread...
Hi:
I'm using SDK V17 & encounter a problem.
in my project, the nRF52832 doesn't broadcast at all.
Once the button1(EVK btn1) is pressed and lasting 5 seconds,
nRF52832...
I'm very new to the NRF boards. I can not find any information on the USB port (programming port). I would like to use that to read serial data written from a terminal program...
I am using the nRF 52840 development kit to explore Thread. I am using the 'open nRF Connect SDK' command to get the project. I would like to use the 'overlay-usb.conf' option...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am developing...
Hello Nordic Devzone Community,
My name is Ted, and I recently posted a question here regarding trouble when attempting to flash a Sparkfun Thing Plus nRF9160 board, using...
The connection is established but no data is transferred between the nrf52840 and the mobile phone(android10). But on android7 or android9 there are no such problems, everything...
Hi,
thanks for your support in advance.
when trying to build with example of sdk, I got the following error. it seems to be related with build env setting... please...
