Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
There have been several other posts on this issue dating back a few years, such as this one .
On Windows 10, if I am using SEGGER's RTT Viewer and I flash a nRF52832 with...
Dear,
As the example code is shown, I have been implementing on LED PWM through nRF53 GPIO0 12. If I set the brightness to 100, it was ON without any issue. However, if...
I use the "zb_sleep_now()" function in the main loop, which greatly reduces the start current. The device wakes up apparently due to the RTC2 interrupt used by the zigbee...
I want to use ncs to get the RSSI at 10ms intervals.
For example, central receives an empty packet from peripheral at 10ms interval.
I would like to know if there is a...
Is it possible to set up an NRF Connect SDK project such that the firmware can be updated over BLE, without including the SoftDevice in the update?
I'm using NRF52810 which...
Hello,
i have searched for uart, i2c/twi communication with polling, interrupt, DMA method different brief explained guide for NRF52
but i have not found it any where...
Hello,
Previously, my nRF52840 DK worked perfectly fine through the USB (J2) connector. Then I successfully programmed PCA10059 by Debug OUT(P19) of the nRF52840 DK board...
My Android app allows the user to un-provision a mesh node. To do so, the app just sends a ConfigNodeReset message to the node's unicast address, which works perfectly if...
Hi, I want to add some auto-test capability to my nRF5340-based project. I thought one useful feature would be to measure voltage AND current at the hot node when all devices...
Hi all
We are switching to nrf-sdk v1.6.0 in our project and encountered a problem with MCUBoot.
The image builds successfully and can be flashed successfully as well...
Hi,
Iam using SDK 17 ,s140_nrf52_7.2.0_softdevice on NRF52840 SDK.For the first time I have noticed an issue,as below on running sample nordic17.0.2\examples\ble_peripheral...
I would like to use the Arduino Nano 33 BLE with MCUBoot and MCUMGR for FOTA. I am wondering if it is possible to use a two-stage bootloader (first stage Arduino BOSSAC, second...
I'm wondering whether the value pointed to by "ble_gatts_hvx_params_t.p_len" passed to sd_ble_gatts_hvx is copied to SoftDevice-owned memory before the call returns NRF_SUCCESS...
