Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I want to make a BLE Multirole application where the central demands LESC, bonding and MITM and peripheral connections is JUST WORKS bonding.
Is that possible? If...
I'm trying to modify the flash_fds example to write a start time when a button is pressed, then an end time when the button is released. I get the time over TWI from an RTC...
Hi, We are into Commercial health devices using nrf5340 and looking to use AoD technology for our device to get its indoor location. We need to have a Receiver with antenna...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
My app uses a proprietary service and characteristic UUIDs; the app needs to completely manage all characteristic reads and writes. With nRF Connect, I can see my service...
Hi Community,
For community's help I success to create 12.3.0 DFU version get work.
So now I try to make all hex(softdevice, bootloader, application) to one hex file...
Dear Nordic,
We are trying to figure out the difference between the working/feature set of nRF_crypto file and mbedtls.
Which one is better and why?
Ambimat
Hello,
I wanted to ask which uart library we have to use in SDK16 and which configuration to have a LOW POWER UART
We are in development phase on the devkit PCA10040 and...
Hi guys,
So i have some Nordic DK board including some dongles, NRF52840 DK, NRF52833 DK running with Zigbee and thread SKD 4.1.0 and make a mesh out of them. But I have...
Hi,
I have to control 16 pin output pins based on the 16 pin interrupt.
Is it possible to have 16 pins interrupt in nrf52840 . Pin change interrupt
when i config
...
I use SDK 15.3, nrf52840.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/setting-up-the-timeslot-api
Normal use most of the...
We are developing a new product that requires extremely low power consumption with a target to run advertising intervals of between 2 to 10 seconds.
We are using the nRF52805...
Hello everybody, My nRF9160 simply does not connect, I already followed all the instructions that come in the quick guide, I successfully registered the SIM card in the nRF...
I am using nrf52832_xxaa with SDK v16.0. I have a requirement to write into UICR register use seggger but I don't see any sample for that. Is it possible? If yes, please provide...
Shalom!
I am getting with the nRF9160, BSD TCP sockets, a connect() errno=116 after disconnecting and closing a previous TCP connection.
I have two TCP servers with the...
