I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi there,
I'm using MacOS Catalina 10.15.6 and nRF52840-DK (2019.9) for the Sniffer. My PCB is running BLE on nRF52840. The hex file used for the sniffer is sniffer_nrf52840dk_nrf52840_7cc811f...
Is there a Hardware Design Guidelines white paper for the nRF52840? I'm looking for something similar to what is available for the nRF9160. For example, this:
https://infocenter...
when I used simulator in keil5 for NRF51 software debug, there is a problem : *** error 65: access violation at 0xFFFFFFF4 : no 'write' permission. When I used the keil5 command...
Hi,
I am using nrf52840 DK and SDK version 17.0.2. I want to write data into particular address location(application area) of the flash using fstorage. It is writing the...
Hello ,
On NRF52840 DK my logger works fine and I get no problem with printf(). However, on my custom board the program goes into hard fault with the following :
0x4001...
Hi there,
I'm using nrf52840 DK and Custom board, SDK 15.1.0, Segger Embedded Studio(SES v5.20)
my issue is when i receive data from uart interrupt based on serial uartes...
Hello Guys,
I'm developping and st7789 IPS screen driver and i'm having problem with SPI0 . I'm using NRF52840 DK 2.0.1
First I took SPI example from sdk 17.0.2 configured...
Hello All,
I am using SES on BMD340 controller with FreeRTOS project.
After few modification in the code, I am facing *.elf doesn't exist during linking stage. There...
On a nRF52833 on a custom PCB, due to space and allocation limitations, I need to run UART Rx and UART Tx over GPIO pins that are limited to standard drive, low frequency...
Dear all,
I have a NRF52832 module (EBYTE E73) and before yesterday, everything was fine.
We had a outdoor test last week and till then, everything was fine.
After...
I've tried this with both 1.5.0 and 1.5.1, with the same results. I install the SDKs using the toolchain manager, and when the installation finishes I open a bash shell, also...
I'm learning how to use OTA DFU on Win10 laptop. I followed this and this guide step by step. I have a couple of questions:
1) (See below code) How to use " arm-none-eabi...
I've recently purchased a Thingy:91 and wasn't able to update its firmware via nRF Connect. I'm guessing this is because that there is no MCUboot on the Thingy:91 that I have...
Have a USB powered Chengdu Ebyte nRF52840 Dongle (PCA100059-style) that has the following:
- USB 5V
- VBUS pin : connected directly to USB 5V
- VDD pin: not connected...
