after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi we currently have a product develeped for 52840 on basis of old sdk 15.3. We are just about to start a new development based on 5340 for which we are required (and want...
Hi Experts,
Recently, I am developing the mesh project based on the latest nRF mesh SDK, everything is running well. But I encountered one issue, that is how can provisioner...
Hi,
I've followed the instruction from " Developing for the nRF52805 with nRF5 SDK" to port the example "blinky_freertos" but I got the following compilation error:
This...
Hi.
I have 3 Dev Board's MBN52832DK and Ill like like to upload the BT Mesh example into those boards and I'm not very expert on this topic, dis you have any Webminar or...
Hello,
i was wondering about the stated antenna efficiency here:
infocenter.nordicsemi.com/index.jsp
The very poor values (< 20%) provided for the efficiency do not...
Hi,
I have experience with the ESP 16/32, pi zero and BOSH XDK. I have been working on some IOT mesh stuff and I have a good product idea that I know I can build with your...
Our project is using SDK 15.3.0 on a nRF25840. Similar to this post , we'd like to be able to re-bond if the bond has been deleted on the Nordic side but not on the phone...
Hello,
I want to test nrf5340 external lfclk, but I don't how to test it.
sdk:1.5.0
board: nrf5340dk without hfclk
I want to use external lfclk to generate 1khz...
Hi Team,
I am developing a device using nrf52832. I want to configure the gpio used to wake up from system off mode to enter into gpio interrupt handler on wake up. How...
Hi ,
I need to add an I2C device in project , I referred sample project i2c_scanner .
changes done in nrf9160dk_nrf9160ns.overlay file
code added in prj.conf
...
We are using PPK II with nRF52840-DK and in zigbee case we are getting two different kinds of reparative pulses
1. Pluse_1 -> Amplitude = 17.52mA ; Ton = 200us & Toff =...
Hi All,
We found a problem about the NRF52832AA connect parameter update problem on some cell phones.
1. While the app connect to our device, parameter update not only...
