Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am merging interactive command and buttonless dfu base on https://www.u-blox.com/sites/default/files/Add-NordicSemiconductorDFU-to-SDKexample_AppNote_UBX-19050198.pdf
...
I just recently got both nRF51422 and nRF52844 DK. However, when I tried to connect through J-LINK, the error message popped up: No emulators connected via USB. Do you want...
Hello,
I built a network of 3 parts. Each has a PCA10059 nRF52840 dongle.
Raspberry Pi 3B+ Border Router using the image from 4.1 SDK. This has the NCP
2X Full Thread...
Hi Everyone,
I am working on nrf52832, I am using sdk15.0.0 ble_peripheral /ble_app_beacon as reference.
I am not understood properly uesd for this function static void...
We just received our latest custom nRF52840 board and have found that there seems to be some issue with PO.19. We have verified that the P0.19 is not working on multiple boards...
Hi
Im using the NRF9160 DK
I have got the Asset tracker working, can modify the code, runs with nrfCloud, beauty
Just followed the docs
But then, I want to...
I have to stream packets from an nrf52 to an nrf24 at a 30 kHz rate using ESB. But when I try to do this, the receiver only receives some of the packets. I don't believe the...
I am using ses and trying to set the max payload length or enable debug mode in NRF_ESB.h. I could of course just change the values in the header file, but I prefer not changing...
Hi Community,
I'm a little bit flyiing in the dark, so I like to ask this in the devzone.
Does anyone already implement NFC OOB Pairing and using Apple GymKit?
1...
We are not using the USB interface on the nRF5340, and thus are leaving VBUS and DECUSB unconnected. Can we also leave D+ and D- unconnected?
Thanks,
Scott
To the kind attention of Nordic support team,
I'm interested in understanding in a conceptual way, how the microcontroller is operating when sd_app_evt_wait is called. ...
We have the following setup: - Both nRF52832 and nRF52840 chips in our product
- The nRF52832 is a module while the nRF52840 is the chip integrated directly onto our PCB...
Hi,
Kit:nrf5340
SDK:nrf connect SDK 1.5.0
1.Can you please explain how the data transfer takes place in ble mesh while using nrf connect SDK.
2. Also tell me how...
