Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi all,
I'm evaluating design for a bluetooth + GPS + NB-IoT ultra-low power device
I see the only possibility to get a such module is to design it (I didn't found anything...
Hello,
I'm trying to auto-build my application through Github actions however I'm running into this problem
When I try to run this locally it works perfectly fine however...
Dear All, I am trying to measure the current consumption for an application I am developing on the nRF52833 DK. The code that I am running is the following: Based on the product...
Dear All, I would like to configure a device to go to the System ON, no RAM retention, wake on RTC (running from LFRC clock) Sleep mode, in order to be able to use the RTC...
Hello,
we are using nrf5 SDK version is 17.0.2 and nrf52840.
Our product uses nrf52840 and its USB capabilities being configured as a composite device (HID keyboard +...
Hi,
i would like to know which software i have to download and install, so that i can program a really basic function like pressing the button and turning on and off an...
Hi,
I saw a Linkedin post by Zephyr where they mentioned some Vscode extensions for devicetree and kconfig:
https://marketplace.visualstudio.com/items?itemName=trond...
Hi,
unfortunatally i could not add a new LTE device. I was able to activate my SIM card but not able to finally add the device to my account.
The error code is: There...
I am currently following the tutorial for creating custom services ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ). The only differences to this...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project. I need to work with another chip through SPI. This chip is the master and...
Hello,
I have one more questions while doing test with SAADC, UART.
When I was tested the SAADC pin connect with ground, the negative value occurs.
So, I changed the...
Hello,
i've built a basic Thread network with two nRF52840 Nodes running the CLI example and a RasPi with a nRF52840 RCP as BorderRouter.
My Question is:
Whats the...
Hi.
Hope you are well.
I want to send data from nRF51822 to nRF24L01+. I used the esb library to configure the nRF51 and I just change the settings as I want ( some settings...
Hello~ I have previously written related articles. But I don't get the answer I want, so I ask you again. Use the toolchain manager to use ncs 1.3.1. The error as shown in...
