after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
For certification purposes to qualify for the QDID defined by Nordic , are there any characteristics that are required to be present in the Device information Service (System...
Dear nordic team,
I'm developing a sensor based on nrf52840 and I want to make use of CMSIS NN. I have already integrated CMSIS in my eclipse project and can already use...
Hi,
Here i am reading the temperature data via i2c protocol , where the temperature sensor is connected to the nrf52832 .(15.2 version sdk) Now i want to publish the temperature...
I'm using nrf52840 with nRF5_SDK_17.0.0_9d13099 and usbd_audio loopback example. The example works fine with the given hex file but when i compile it myself, the signal seems...
Hi :) ,
My project continues quiet well, and now come the time to create final assembli of all my small block.
I'm using nrf52833, with s113.
I want my device...
hi guys,
now i have 2 pieces 52832 boards; A(PERIPHERAL) and B(CENTRAL); both run the nus service.
B( CENTRAL)--->A(PERIPHERAL) Through ble_nus_c_string_send();
and...
Hi. I need the NRF52832 to work in two modes. After power-up, the radio module worked like a normal NRF24L02, and after pressing the button, the BLE started. I took the example...
Hi Team,
We are working on the nRF9160 DK. We are integrating the central_uart code into the lte_ble_gateway, As we integrated for the purpose to use NUS(nordic uart service...
Hi,
I am developping some kind of driver as my company calls it which will be used to easily setup a mesh network for our projects. I am using the light_switch_client_example...
Hi,
We are using nRF52840 Dongle to receive BLE peripheral Device 240 Bytes notifications for Win10 program. And w e used "pc-ble-driver-4.1.1\examples\heart_rate_collector...
Hello Nordic
I am working with nrf52832, sdk 16.0, softdevice s132
I need to advertise NON CONNECTABLE ble with changeable data (later relevant data will be received...
Hi
we are using the nRF52840 and antenna signal i connected ceramic chip antenna(ACAG020-2450-T).
The above attached schematic of ant signal matching circuit schematic...
The only way I can see to do it is by two separate PPI calls. So Timer1 "tasker" is firing both the capture and clear... but will they execute sequentially?
