Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
Hello,
i'am trying to control the pwm Idle State Level.
between my Sequence's (1sek) the PIN stays High But i need it low.
I try to set the GPIO Out Register, but...
Hello,
I am working on a simple Bluetooth mesh example setup with the following configurations:
nRF52832 DK: light switch server, subscribed to group 0xC000
nRF52840...
We have a mobile app on iPhone and Android, the NRF52 advertises every 3 seconds. The app can discover the NRF52 quickly but it takes a long time to connect. The iPhone is...
Hi,
I am developing a system that will read from a sensor that uses I2C and then transmit this to a "master" using ANT+ or BTLE (this isn't decided yet)
For the prototyping...
Hello,
Where can I find the pre-built binaries for the below Provisioning options :
1.OOB (Public Key) and Authentication - Input
2.OOB (Public Key) and Authentication...
Hello.
I have an nRF51822 chip and I'm trying to figure out how the whole nRF5 sdk works.
I am using the Segger Embedded Studio.
I downloaded the last nRF5 SDK v15.3...
Hi!
I'm trying to use the AWS-FOTA sample, I flashed the sample onto the board and it connected to the AWS account successfully, but when I try to add the update.bin file...
Hi. The main loop of my app is mostly doing SPI communication to a GPS receiver. I'd like it to do that every second or so and spend the rest of the time in system on but...
Is it possible to configure the ACL to protect the UICR registers?
If so, would this have any impact on the SoftDevice or other nRF52840 peripherals? I.E does the SoftDevice...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
Hi
I am a beginner in the MCU and SoC realm. I was checking the nRF52810 WLCSP33 specs but could not find any mention of the bluetooth range. Is it a standard range for...
