Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Add whitelist function in \ nrf5_sdk_15.2.0 _9412b96\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay, and report error 12804 (0x3204) after disconnection...
I'm trying to use the SAADC to return one value so I initialize it, try to take the reading, then unitize it so I can use it for taking readings through the PPI. The SAADC...
By default, is it enabling or disabling bias correction? If no, how to enable bias correction?
Is the RNG peripheral being left on all the time as a result of us using it...
hello,
I need send 10000bytes large data send central to peripheral in single transmission. I using example code ble_app_uart_c in SDK15.2 nrf52832. what are the parameter...
Hello
I am writing low-power application where NRF is called from the other chip by interrupt, performs bluetooth scan and sends data back over UART. Of course, I want to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
I am using ‘ble_app_bliky” for my application development. In this “Button...
Hello =)
Im trying to run the ble_app_uart_c example on a NRF 52810 Chip.
i got:
SEGGER Embedded Studio for ARM V4.12
SDK 15.3.0
examples\ble_central\ble_app_uart_c...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
In ‘System OFF’ after GPIO interrupt, chip will reset and control will come...
Hi All
I am using nRF52832 with softdevice s132_nrf52.6.1.0
and I have to use both protocol (ble & gzll)
the default protocol is ble
after i keep pressing the button...
Hello,
I am working with nrf51822. I have developed a custom evaluation board. Accidently I connected voltage in reverse polarity to the device now i am unable to program...
Hi,
I am trying to understand possibilities provıded by Bluetooth Mesh Technology.
In my topology, there are tywo types node.
The first type of node is connected to...
Hii,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 2.0.1.
However, when I try to increase...
Hi. I'm using a nRF52840 chip and have a flavour of Proximity profile example being used with some custom services and characteristics that have been added. All is good in...
There is my function for writing to flash.
It works when NRF52832 start from reset, if works when the NRF52832 gets data over BLE but it does not works after "power down...
Hello, for some reason, the UUID's on a Galaxy Note 3 are messed up or are not being read properly. I have included screenshots of the issue. The note 3 is running android...
