I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi
Im using the DFU secure example (examples\dfu\bootloader_secure\pca10028)
Im working on a NRF51822-QFAA ,S130 SDK12.3 , Im not sure about my IROM/IRAM definitions,...
Hi Nordic Team, One of our customer wants to integrate communication via Thread BLE on his IoT-Gateway. We found your nRF52840 Dongle. Does this dongle have any certifications...
Hi,
I am planning on using nrf52832 for a beacon application. I happen to get a schematic and layout from Nordic website for development.
I am attaching the schematic...
Hi, I am trying to interface MPU^)%) sensor with NRF52832. with help of BLE UART. i will get the resultant data on BLE APP. but here i got some error is this the linking error...
Hi,
we want to made the device which should working in the mesh network without provisiong procedure by user.
Typical application - network with 500 nodes, every node...
Hi, I am using nordic nrf52832 module with BLE mesh SDK V2.2.0 I want to do DFU for application + softdevice without any serial connection through mobile app between BLE mesh...
I got the fail result of the test CPS/SEN/SPE/BI-05-C [Cycling Power Control Point Procedure Timeout].
At this test, the tester does not send the confirmation until ATT...
Hi Team Nordic,
According to the AM2302 (DHT22) datasheet, the data pin will be pulled to high state in idle state. But in my case, when i am reading the data pin before...
I'm developing nFR52832 to communicate with the PC via UART. commands are sent to the nRF and for each command nRF responds with some data back to the PC via UART.
The UART...
I'm trying to include the SPI driver in my project.
I have added the .c file into my project:
I have included the path into the project:
I have enabled the SPI...
I try to make bootloader via USART for my application. I'm using: nRF51422rev.2, SDK6.1.0, S210 ver3.0.0. KEIL5.11. I did everything like describes in post here:
devzone...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
