Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I want to add the function about bonding and passkey to the example of " ble_app_hrs_freertos...
I have an application where in i need to scan for non connectable advertisements as well as advertise beacons on the device. I am using the Fanstel BT832A module which contains...
Hello,
i would like to interface nrf51822 with an rfid reader mfrc522 using SPI.So, i went through the example of spi_master in SDK 8.1.0.How can we access the value of a...
Hello all,
I am right now working on one project. where i use nrf52832 BLE board. right i am doing i2c communication of temperature sensor(lm6bd) with ble board. but can...
Hello All,
I am using nRF52810 programming in segger embedded studio in windows 7. i am trying to do i2c communication between sensor and nRF52810.i am create custom service...
Hi,
I have a question about direct advertisment - if I direct advertise to one android, then other devices won't show it am I right? How does this direct advertising works...
Hello all,
I am using nRF52810 programming in segger embedded studio in windows 7. I am refer SDK nRF5 v5.2.0. I am trying to do i2c communication between sensor and nRF52810...
I had a couple of questions regarding the SPI slave peripheral on NRF52:
What is the behavior of the peripheral if a transaction completes (NSS goes high) and another...
I used the example code of MQTT pub and sub with nRF52 DK which has nRF52832 in it. I have sent the data from one kit to another with the help of Raspberry pi 3 as a router...
Hello. I need a bit of help with my case. I have nRF52832 dev kit. I have set heap size to zero in Makefile:
And even with that change I am still able to allocate memory...
Hello,
I have some questions about NFC on nRF52832:
1.Could NFC on 52832 works as a card reader , for the mifare 1 card, or named S50 card?
2.In the example "nRF5_SDK_15...
Hi all,
I have read that ANTUSB-m is needed for ANTWARE running in Windows PC. Can I use nRF52840 DK or nF52840 USB dongle in place of ANTUSB-m? If yes, where I can find...
Hi all
I have a custom Board, I have tested it a lot. NRF51822, programed with Mbed..
In general the Software and Board WORKS FINE, but I found some problem in my procedure...
