Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I build esb_ptx example in sdk12, download in nRF52832 board, but from uart tool, I can not see log.
I have enabled log in sdk_config.h, and in options for target 'xxx' ...
Hi,
I have a DFU issue. Using Visual GDB IDE and gcc tool chain.
I Can get my signed application generated into zip then DFU it into the device which all works.
Once...
Looking at the radio notification code in components\ble_radio_notification, it looks like there isn't an option to use the NRF_RADIO_NOTIFICATION_TYPE_INT_ON_INACTIVE event...
Hello,
I am reading mpu9250 and providing timestamping with events. I want to create timer so that when the timer will be called reading of mpu9250 will begin and when...
Hi there
I have encountered another issue with a repeater that I am working on.
The program follows this basic sequence:
Setup as NRF_GZLL_MODE_HOST
Wait for...
Hi, I am trying to use NRF_CLOCK_LF_SRC_RC as clock source with the following settings:
pca10040.h
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_RC,
.rc_ctiv...
Hi,
Am having application with Freertos in which am creating 4 tasks + ble task using Freertos API's. Application is running as expected without any issues.
But in 4...
Am flashing SD 3.0.0 and secure Boot loader and then updating application (with Freertos) via bootloader .Application boots up no issues.
am facing below issues.
1.Am...
Hello,
I've checked the timing diagrams for the CE and IRQ on the datasheet but I would like to know if anyone has actually tested them with an oscilloscope? If yes could...
I am using SDK 11.0.0 on a nrf52832, with FreeRTOS and SD132 2.0.0. I configure the FreeRTOS port so that it uses RTC1 as SysTick. Depending on some compilation macros, my...
Assuming that all peripherals that require the high frequency clock are disabled / turned off / stopped, how long does the HFINT oscillator run after calling __WFI()?
And...
What's the delay from setting the Start / Stop task in an RTC module to when the RTC actually starts or stops? Is it less than 1 clock cycle on the CPU (15ns)? More than one...
Hi, I am using the nrf52 dk to sample two analog inputs through PPI.
My question is if I can use different bit resolutions for each analog input?
-Erblin
