My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I have one nRF52822 Ble. It has secure pairing mechanism.
when i connect iphone, App trigger Pair dialog from iOS. and press pairing, then stop.
i can follow nRF52822 code...
I've ported an nRF51 DK project over to the nRF52 DK and the only issue I seem to have with the nRF52 is that the device refuses to pair with my peripheral, hard faulting...
I used the nRF51822 for my thesis and as I was looking for the url of the product spec I used I noticed something strange:
My product specification for the nRF51822 is version...
I've connected my nRF51822 mKit to my Linux system via a USB cable. While trying to upload code on the board, I got the following error:
SEGGER J-Link Commander V5.12g...
Currently i was using arduino for my development but now i want to move forward with Some SOC so i found nrf51822 IC.For using nrf51822 ic i need to buy another board which...
I would like to use the nRF24L01+ for a telemetry project that requires broadcast at 100% duty cycle at a fixed bitrate. Ideally, we could also use our own frame format. ...
I am trying to use whitelisting and a passkey to add security for my application. So far I have the passkey set up so that it is working on the master control panel on PC...
Dear sir.
From [nRF51_Series_Reference_manual], ADC maximum input voltage has two rules.
The ADC should not be exposed to higher voltage than 2.4 V on an AIN pin...
hi
i have one custom service that have 6 characteristics
when in android i want to write in one of characteristics it take about one sec .
is this for having 6 characteristic...
In the Androir master control panel app, in the scanner results there is a 'Type:' line for each device. Most of them around me say 'UNKNOWN' however some say 'BLE only'....
SDK 11.0.0, S132 v2.0.0, nRF52.
I have searched through the many questions already on the dev zone on this topic, but cannot solve my problem. I tried adding the dfu service...
hello all,
i am a begineer to nordic . i am trying to read adc PCF8591 value through TWI and i want to print the value in UART TERMINAL.
i have written the code. but...
Hi,
Im trying to connect ble_app_uart to my gsm module. For some reason program fails at runtime. I was expecting to find a filename and line number where the error has...
Hi,
nRF52 Board, S132. Now, I want 6 pwm, 6 adc .
nRF52 has 5Timers, Timer0-Timer4.
Now, I allocation these timers as follows:
//TIMER0 is used by softDevice
APP_PWM_INSTANCE...
Hi,
I want to access restricted peripheral: TIMER0.
After small research found that I should use sd_ wrappers, in my case sd_nvic_SetPendingIRQ(TIMER0_IRQn) however I...
