Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
What should I change to run the hci_lpuart sample with UART asynchronous API instead of the using the interrupt driven one? I have already changed the source file on the sample...
I was able to run blinky successfully on my customized nrf5340 board, but it doesn't respond to writing matter related code, there is no output from the RTT, I refer to the...
Hello,
I am reaching out regarding some challenges I've encountered with SPI communication on the nRF7002DK when interfacing with the ETH Wiz Click | Mikroe module and a...
Hello,
I am a student and new programmer and got the Thingy:91 for a project at Uni. I went through the getting Started guides and now I am at the point, where I downloaded...
I tried adapting the blinky sample project to work with a custom board. After an hour or two I was able to define the GPIOs of my schematic including I2C with the device tree...
Hello,
we are trying to implement a custom Friend node research policy, before the friendship is established.
Since bt_mesh_lpn_poll() works only when the frienship is...
Hello,
is there any example using the IEEE 802.15.4 driver?
I was able to send and receive a some packets by using nrf_802154_receive and nrf_802154_transmit_raw, and...
Hi,
i am playing around with configuration of Softdevice (S112 ) + bootloader + application.
Bootloader is custom, really simple. Flashing block of data received via uart...
Hello, I wanted to understand what is the default storage place in the internal flash memory region of persistent info for OpenThread. In the previous SDK (Thread and Zigbee...
Hello DevZone,
I have 2 Thingy91X (not Thingy91), with nRF9161 and nPM1300 inside. These two devices run out of battery for several hours.
The problem is that I can't...
Hi，I have some problems using the NFC routines in the SDK.
The hardware used is nRF5340 DK.
Software is nRF Connect SDK v2.6.99-cs1.
The downloaded and run routines...
Hi,
We have designed a custom board for npm1300 and nrf52832(MS50SFA2 module). We would like to drive the VCC of the BLE module using buck2 but we are only getting 1.8V...
Hi,
I have to use Nordic SDK and VS Code Dev Kit on my company enterprise PC but I cannot fetch the toolchain or install SDKs via VSCode or nRF Connect for Desktop
...
Hi everyone,
I'm the author of the following question and a lot of context information about the state of our custom application can be gathered from there: registration...
Hi,
In my app I have been using the following to register my state change callback. This works. Only issue is it seem to only pass ot_instance, I cant pass a user data to...
