Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am using nRF52832 board with the SDK version nRF5_SDK_15.3.0 and soft device S132.
I have implemented the POF(power fail comparator) to generate event when the event...
I've got a project that I'm going to want to do DFU through the UART, and in order to transfer files in a follow-on activity, I want SMP running in the application. Therefore...
My question is related to LE Audio, i guess, since i have no previous experience from it. Is it possible to have a device as a peripheral for mobile phone sending data to...
Hello Team,
We would like to keep the necessary build configuration for a board in Bitbucket,which are necessary to show up the "Build" folder in VS code.So that every developer...
In our project we want to trigger the saadc with the lp_comp and read Analog input once for 2s (with 2000 Samples). In the lp_comp_handler we call:
We have set the Sample...
Using SDK 2.1.2 Trying to set up connectable advertising for specific period of time and be notified when this period of time expired. My setup sequence (simplified for demonstration...
Compilation environment ：nRF Connect SDK V1.4.2
I successfully subscribed to a notification property of the peripheral using bt_gatt_subscribe, the callback function is...
We are converting our existing product firmware from the NRF environment to Zephyr. We use both simple PWM for which the conversion is no problem, and the more complex PWM...
Hello.
I am trying to learn how to implement unit tests for embedded c-application. I created simple example about my problem and I am having hard time actually running...
Hi Nordic support team,
I'm new to Nordic chip and using nRF5340 Audio DK for my project,
and I'm trying to build zephyr/samples/blutooth/iso_broadcast_benchmark , which...
Hi.
I'm doing a customized board with NRF5340 and need to minimize all the general inductance on the board.
I would like to change L2, L3 and L4 to 5.6uH. Is it possible...
Hi,
I'm using a circuitdojo feather nrf9160 I want to use the nRF cloud but I got some trouble connecting. Something is missing, but don't know what.
This is what I did...
Hello everyone,
I am using the Power Profiler Kit II (PPK2) to measure the deep sleep current of an ESP32-H2 when running the boilerplate OpenThread deep sleep SED program...
Hi
We have nRF52840 + FEM in our design. Output power level is mainly controlled by the nRF52840 TX power setting which drives the FEM. However, the txpower options is...
Hey, After updating the nRF Connect SDK v2.60 (from 2.3.0) package an attempt to turn a BLE carrier ON by sending the BT_HCI_OP_LE_TX_TEST_v4 DTM command over the HCI interface...
