Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I would like to test he Wi-Fi Provisioning Service sample ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/wifi/provisioning/sample_description.html...
I'm trying to implement a central BLE device with pc-ble-driver. Central and peripheral devices should be paired with a passkey, and they use custom UUID. The connection is...
Hello,
I'm trying to differentiate between different peripherals connecting to a central (52840 using nRF Connect 1.8.0). Using the following code I'm able to get and print...
Hello,
I developed an application for a custom nrf52832 board. It uses the Nordic UART Service (NUS) to transmit data over BLE. This works fine.
At the moment I am trying...
I'm thinking to have a cental_and peripheral at the same time.
Using the the standard ble I have to setup the configuration.(Who is the Central_uart and the Periheral (...
I'm profiling the current consumption of our device, on an nRF5340 module, at SDK 2.1.0.
So far as I can tell, the ADC is using approximately 1000 uA. It's sampling via...
Hi,
I'm using PCA10100, and developing my project on examples\ble_peripheral\ble_app_uart(SDK 17.1.0)
I connect P0.08_8 and P0.06 with other sensor module's uart, when...
I'm developing a BLE application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice. My application involves using some software...
Hi, Nordic:
I am trying to use spi to transfer data between the two DKs. But I'm having trouble emulating the use of spim to use spis.
This is my main.c.
And this...
In the nRF52840 datasheet, peripherals don't appear to have shutdown or power-off controls but they do have enable/disable registers. I'm guessing that Device PM turns on...
Hi, I use periodic advertising to send live data based on readings from an accelerometer. I want to change the advertising packet after every advert to the new values.
My...
Hi there,
I am currently building nrf9160 custom board. But now I am planning to implement provisioning credentials like this URL https://docs.nrfcloud.com/Devices/Security...
Hi
The response to this ticket
says "You can implement active RFID. In active RFID you can for instance periodically wakeup the chip to turn ON the radio for a short...
Does Nordic provide a DTM application for the nrf5340 which communicates over the USB interface as a COM class instead of using a UART interface? It's been brought to our...
Hi Nordic team,
I debug on the board, and I want to check the connection at the first time without connection before. so I want to clear data on the flash first, then...
