I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I’m working with an nRF52840 that supports Bluetooth Low Energy updates via MCUboot.
We want to enable APPROTECT on our production units to prevent competitors from...
My understanding is that when the module's measured RSRP is lower than that defined in the broadcasted SIB, ECL will be escalated to higher level during RACH process.
Besides...
Hi,
I found out that my Matter device does not commission to Alexa because as part of adding the device Alexa will try to read FeatureMap attributes from all clusters and...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
I have a quick question about configure i2c.
I have the following schematic:
And the following configuration for the nrf54l15 :
And the following in prj.conf:...
Once the nRF52840DK is running the Zigbee light bulb demo I cannot flash new code to it unless I disconnect the board and reconnect it first.
I am using nRFConnect for Visual...
Are there user programable once registers on nrf5340 that I could use to store board hardware version? I looked at UICR, but I think they get erased when the whole chip is...
I added FOTA over Bluetooth to my NRF52840 application. Everything works, I can update the application over bluetooth and it runs properly, but after updating if I unplug...
Hello Nordic support,
I would like to understand how I can decrypt the packets that is using Legacy passkey pairing. Here is the BLE sniffer log, where I selected Legacy...
Hi my ffriends,
I’m working on a wireless system called for me " Wireless Link Project" , based on the nRF24L01 (non-Plus) transceiver.
I have two identical boards using...
Hello DevZone,
I have a confusing question about TF-M. Need help from a TF-M expert.
In this document , it says that we must disable uart1 in non-secure application, because...
I'm trying to test the overall pwoer consumption of my setup (nPM1034EK and nRF54l15DK) using the PPK2. As I've started this, I've gotten far higher numbers that I expected...
