Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Question: Based on the chip nrf52840, I want to design a product application that can work with matter and thread at the same time. Is it possible to implement this design...
Hi dear team, Im currently on the NRF9160 DK (0.9.0) trying to get SPI up and running.
nRF connect SDK v 2.1.1 using visual studio code. However Im having problems getting...
Are the memory-mapped hardware addresses (e.g. 0x40000000 and following)
on the nRF52840 mpu restricted from access by the Zephyr RTOS.
If so, can this be defeated ?
Hi, I'm using NCS v1.9.1, and attempting to upgrade MCUBoot via DFU over BLE using the nRF Connect for Mobile app.
I'm able to successfully DFU the application image. However...
Hello,
nice to see that you've updated your documentation website ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/releases/release-notes-1.1.0.html )....
HI I am having trouble converting the NUS example into something that simply stores the BLE nus response to the peripheral into a variable rather than printing it to the UART...
Hello all,
I am developing on the nRF52840, and I am using the PCA10056/nRF52840-DK to assist in my understanding of the uploading process.
Currently, I am trying to get...
What is the reason Nordic dont want to provide yet dual mode solution - BR/EDR + BLE? - There are plenty of legacy BT devices on the market and the new BLE devices doesnt...
I am working on developing an application for nRF52833 DK (PCA10100) using nRF5 SDK_v17.1 and nRF_802.15.4 Radio driver v1.6. I am using the s122 Soft device on the device...
Hi all,
So I was following this guide for updating my firmware over BLE: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu#dfu_over_bluetooth...
Mesh SDK 5.0, SoftDevice S140 v7.2.0, NRF52840, SEGGER ------------------------------------------------------------------------------------ Hello, My problem is that I can...
When i open the Toolchain on my mac it loads and put upp a crash page. i have already: restarted my mac, reintstalled and restarted but i get the same crash
The System...
Hi, I currently have a project with an nRF52832 chip using SDK 14.2, I would like to upgrade the project and change the chip to nRF5340. Is there a way to migrate the project...
Are there any examples showing use of the MQTT library using Bluetooth as the Link Layer? I see this on Zephyr's repo zephyr/subsys/net/l2/bluetooth at main · zephyrproject...
