Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
I use the nRF52840 board and am currently working on a Matter project.
I am trying to add a cluster to an existing Matter sample project as per the link guide below...
Hi,
I am working on pdm mic integration in zephyr RTOS. I used INMP441 mic sensor. I got SPL in dB by using nrfx. I want to create a driver for this mic. Please help me...
I have an nrf21540-ek. I hope it can be used with my nrf5340-dk. Does NCS 2.0.0 contain relevant drivers or does the driver need to be implemented by me? If NCS 2.0 contains...
Hi, recently I am been consistently getting the same issue as this post, despite having successful performed the Mesh DFU in the past and with the example code:
I suspect...
Hello,
My goal is to make DFU over a mesh network.
Using this guide , I did the following:
nrfjprog --program bin/softdevice/s132_nrf52_7.2.0_softdevice.hex --chiperase...
Hi there,
We are developing our own uart driver, and need to understand the power consumption of the peripheral.
According to the product specification section electrical...
I'm using VS Code and the nRF Connect extensions to build a project that is derived from a sample app. It was created as a freestanding project, so the SDK is shared with...
Hi, We are using the nRF Connect SDK and building a Zephyr standalone application. Is there a way to add a post build step to the application CMakeLists.txt file which will...
Hi all,
As we will al agree refering to the BLE standard, a SCAN_REQ Frame contains 176 bits (22bytes), and since the BLE legacy standard datarate is 1Mbit/s, the duration...
Hi.
I'm working with an NRF5340DK using NRF Connect SDK in a project where I need to decrypt an input text with a previously adquired key usign AES128 CTR, but I've been...
I use two 52832 generic_ onoff_ In the example of server, a mesh network is formed. Both monitors the group address C001. I put the other one outside the range. Then the group...
Hello,
I have a project that requires Bluetooth, Zigbee, and WiFi.
I want to make sure that the following is possible:
nRF52833 or nRF52840 can run Bluetooth and Zigbee...
I am testing I2C. But nrf_drv_twi_tx() failed with errCode 0x8201. What is meaning of 0x8201 error code?
<warning> app: nrf_drv_twi_tx() failed, errCode=0x8201
Dear Nordic,
We're developing an application using the nRF52840 as a peripheral. In the role of central we have three different devices we're using:.
Android Pixel phone...
I used 9160 to develop a project for the customer. During the project test, sometimes the data line or clock line level of I2C was abnormal due to hardware reasons. I wonder...
