Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Nordic,
Using nrf-connect 1.9.99 and Zephyr 2.7.99 (*** Booting Zephyr OS build v2.7.99-ncs1-1 ***)
I am using then nRF9160-DK and everything is fine. Getting 40uA...
I'm running Manjaro Linux and have ran through the installation instructions for the nRF Connect Desktop. I have separately downloaded the Segger JLink software as instructed...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hello, I am using 52832. There is an external interrupt count with a maximum frequency of 1kHz. I have two hardware. One I transmit to the mobile phone at an interval of 50ms...
Hello sir ,
i am trying to build file from given sample code file name is "azure_iot_hub" , i don't make any changes in this file .
on adding build configuration it show...
I have an issue from few days with the nrfCloud.
I am not able to see the live data from my devices.
However historical data is available up to the last sending so the...
I can't quite seem to figure this one out.
We've got the APP_ERROR_CHECK macro on our functions that return NRF errors. When there is a genuine error, the system does not...
Hello, I am trying to communicate with a Bosch BMI 270 device( datasheet ) using the nrf5340dk. I originally tried to use I2C since there was an example file available for...
I have an issue when registering the SIM card on nRF cloud. The save button on the form shown below won't active and can't be clicked. I have tried to fill just the asterisked...
Can anyone comment on, or point me to specific documentation, regarding creating custom control points under nRF51? I'm using both nRF51822 and nRF51922 parts. I have read...
I have a semi-working app which executes Zigbee commands that it receives from other nodes, but the latency is sometimes unacceptably high. I would like to check some of the...
Hello All,
I want to use the io function of freertos, but there is no routine for nrf52833 to use this function in the community and Google, so I want to ask whether the...
I used mergehex.exe to generate a merge.hex with firmware appcore.hex and firmware netcore.hex.
and use nrfjprog.exe flash merge.hex to nrf5340.
Prompt error:
How...
Hi,
I want to simply get RSSI at each scan in the connection less example (direction_finding_connectionless_rx). I have running two nRF52833-DK. One is flashed with RX and...
Hi,
I would like to know if there are sample programs for getting GPS sentences through UART using Zephyr. I am using Fanstel (BT840X) board. I would also like to know the...
