after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi ,
1. How do I port the NCS V1.8.0 asset_tracker example to NCS V1.9.0
2. The customer code was developed in asset_tracker and failed to port to NCS V1.9.0
Thank you...
Hi,
I have a few thingy:91 devices (~10) and when using the IBasis SIM card, I'll randomly be connected to Telus, Bell, Rogers or Videotron. Some of them do not support...
Hi,
I have implemented BLE OTA DFU using SMP service (I integrated SMP sample ) on nRF25833. Version of NCS: 1.8.0.
I have tested it with nRF Connect mobile app and it...
I want to make a thread protocol based luminaire product, there will be 300+ luminaires and 10+ OTBRs, and then control them through the cloud platform. Now I need to verify...
Hi. I apologize in advance if this question is in the wrong place or is too elementary for this location/audience. I have prototyped a product using two Nano 33 BLE arduinos...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now I'm debugging to add one new feature, but some time...
Hi
I want to use a mcu to update the firmware in the nrf52810 through uart,I look in the sample in the nRF5SDK1702d674dde\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader...
I try to update/replace the code in a nRF52 board from 3rd party (Fanstel). They only able to provide the private key which I can create the zip file but not able to give...
For our application, if the device loses connection, we enter beacon mode for longer range, and advertise using extended advertising to broadcast more data. Beacon mode wit...
Hi, I send application data using Read blob PDU from nRF52832. nRF52832 firmware is connectivity of Serialization of nRF5_SDK_17.0.2 for UART interface.
After connection...
I have followed the Scheduler tutorial ( https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/scheduler-tutorial ) and was able to use...
Has anyone characterized the nRF5430 ADC dynamic performance such as harmonic distortion, SFDR, SNR over frequency. I am interested in the 10-2kHz frequency range.
Th...
Hi,
I just want to know is there any Pre compiled hex files are available to convert my Thingy 91 as Thingy 52, I just want to use my Thingy 91 with Thingy 52 Bluetooth...
Hello,
I am developing a custom board using NRF52820 and I am trying run the Blinky example on it with no success.
I am trying to adapt the blinky example for PCA10056_S140...
hi support team,
i searched devzone, my question are similar with "devzone.nordicsemi.com/.../349118
it is clear we can't set it manually. and there is no API to achieve...
