Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am using an nrf52833-dk for development, and I need to work out interrupt based SPI. Can you kindly point me to an nCS based sample project for interrupt based SPI...
Dear Concern,
I want to keep my nRF52382 module in low power mode during non operational condition. During the TX and RX condition it has to wake up from the sleep mode...
Hi Team,
I tried the blinky example for the nRF52833 DK with the nRF5_SDK_17.1.0_ddde560 . I am using Segger Embedded studio for ARM V5.62 64bit – Non Commercial License...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
The program is created by referring to the whitelist of "ble_app_hids_mouse" which...
1. in the file "Core_v5.2.pdf"
"The LE system operates in the 2.4 GHz ISM band at 2400-2483.5 MHz. The
LE system uses 40 RF channels. These RF channels have center frequencies...
1. I'm runnig the asset tracker fine with nRFCloud. When I run the cloud_client, I get this log:
*** Booting Zephyr OS build v2.7.0-ncs1 *** W: Already initialized. Nothing...
Hi,
Referring to this - https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/devicetree/bindings/net/wireless/nordic,nrf21540-fem.html I understand...
Hello everyone! I'd like to implement the nrf52-ble-image-transfer-demo with a nRF52840 Dongle, for a small low-power image transfer application. My question now is, how do...
I am trying to use Visual Code environment (on macosx Intel macbook pro) to program nrf52840 dongle.
The dongle is found and programmed with using nRF Connect for Desktop...
Hi Nordic，
One of my customer has a problem about 2M phy.
They use 52840 connected with IOS via 2M phy.
They set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL both to 20...
Hi, I'm working on nRF9160 with Zephyr (SDK 1.7.1) and one SPI device. I analyze CS signal with correlation to SPI SCK. Is that normal that CS signal stays low much longer...
I am trying to add a Nordic Thingy 91 to my azure Iot hub.
i've configured the device according to the guide
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I noticed when using the UART BLE Example that there is no password or pairing request to connect to and use the device.
Everything works fine, and I even implemented my...
I followed the official tutorial. The programmer 2.3.3 in nRF Connect for Desktop v3.10.0 in Linux has problems programming the nRF52840 USB dongle rev 2.1.0 in DFU mode....
