Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello
Is is possible to enable MCUBoot image compression on nRF52832 ?
I tried to enable it following this blog post but I got a compilation error :
Compiler insulted...
Planning on using the npm2100 PMIC as our PMIC for an upcoming asset tracking solution. We will have an accelerometer that will determine when the main MCU (nrf54) wakes up...
I am using peripheral_uart as my base project. Right now MTU value is 23 I believe as I can receive only 20 bytes of data at a time. How I can increase the MTU size with configurations...
Hello,
in use is the nrf connect sdk v2.6.2 toolchain v2.6.2 on my nrf5340DK
I struggle transmitting ADC data from my nrf5340DK via USB to my windows PC. On my PC there...
I've added some debug information to the build of my application. The added stack usage has caused some threads (USB, BLE) to overflow the stack and cause random crashes....
Hi,
Is there any better block diagram of how power is managed and routed within the nRF7001/ nRF7002 device ?
I see it has a buck from BUCKVBAT fed back to several other...
When trying to open certain c or h files in my project, Segger Embedded Studio (latest version) gives a very longwinded uncopyable dialog message that there was an error decoding...
Reopening this issue from three years ago
as the original question was not answered.
So I had this line of code after sd_softdevice_is_enabled 'returns' false
but...
I am trying to communicate with multiple devices using ESB. The host device must queue data in the TX FIFO as ACK data before receiving the data. I want to keep data queued...
Hello! I am developing an application under the SDK V2.9.0. Now I am trying to set up a simple project with a sysbuild, Mcuboot and a partition manager. Here is the file tree...
Hi,
I’m currently using nrfx libraries when there are no equivalent options in Zephyr drivers, and I found similar drivers with the nrfy prefix. What are the differences...
Hi
I would like to use DeviceTree in VS code. The VS code had installed "nRF Connect for VS Code Extension Pack" and tools chain.
But I can't see any file in "DEVICETREE...
Hi Nordic DevZone Support,
I am facing an issue with my custom PCB using the nRF52840 microcontroller and Zephyr NCS v2.6.1 . The same firmware works on other PCBs , but...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
