Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We are integration the Onomondo softsim in our devices.
The precompiled libraries in the SoftSIM repository are compiled with floating point Soft ABI selected. See developer...
Hi there
I have started a project from the green field. After adding some threads and for some blinky examples, I want to enable bluetooth on my nrf5340dk. taking inspiration...
Hello Nordic Team,
I’d like to request the addition of an AI-powered extension as part of the existing nRF Extension Pack for VS Code . The idea is to integrate an AI assistant...
Hi Nordic Team,
I am working on a Smart Panel implementation using Matter, which contains multiple switches (e.g., 16 buttons) and some sliders. I have a few questions regarding...
Hello everyone,
A nRF52832 with SDK 15.0 was used for my application. I am trying to send a large amount of data via BLE with a custom BLE service. I extended MTU size so...
nrf5340 net core Konfig
nrf5340 main.c code below, I changed options
nrf54l15 main.c is below
I add the tx power print in PAwR recv_cb function.
Below is 54l15...
Hello there,
First of all, I had searched similar issue internally but didn't find any solution.
My problem is for my application with DFU buttonless without bond everything...
Hi, I am running the raw_tx_packet sample (ncs v3.1.0) on nrf7002dk with the following configuration (additions to prj.conf in the sample)
The captured output looks like...
The channel_sounding_ras_initiator/reflector samples work but trying any other combination of parameters for bt_le_cs_create_config_params or bt_le_cs_set_procedure_parameters_param...
Hi Nordic,
I am evaluating the nrf52833 DK with nrf connect SDK. I am using by dev kit here as a central devie and I want to get the RSSI values of the periherral devices...
actually a general question, though i'm working with the nPM2100 EK....
assume my target MCU operates "most efficiently" when supplied 1V8 -- expressing overall energy consumption...
We are using an MCU that pushes data packets to the nRF9151 communication module via UART. According to our module service provider, each data packet can only be up to 2 KB...
I am testing PAwR interoperability between:
TX side : third-party chipset acting as PAwR Advertiser/Transmitter
RX side : Nordic board running nRF Connect SDK...
Goal: "I am trying to get SPI3 working with a custom MAX30003 driver in a sysbuild non-secure ( _ns ) application, based on the peripheral_uart example."
Problem: "The...
Hi,
I have been evaluating the use of nrf9151 using two development kit boards.
On my first board, I set it up initially using quick start under the nRF connect app...
