Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi DevZone,
1. Description:
I am going to use the nRF9160 SiP in a project on a custom PCB which will house the (LN60G840F, which has an nRF9160 on it). The application...
Hi support team,
I have a nrf 51822 beacon black version and developing with nRF5SDK1230. i'm learning about update firmware for it over BLE. i try to run example dfu/bootloader_sercure...
Hello,
I'm using an nrf52dk board and I am trying to get the RSSI value, and it works fine with the nrfconnect app, except that the the transfer doesn't start at the first...
Hello guys,
I want to work with NRF Mesh but I need help with answering some general questions:
1. Is the current version of the SDK ("nrf5_SDK_for_Mesh_v5.0.0_src") power...
HI,
In my custom board of nRF52805 , I am able to program basic UART application. chip is also generating internal voltages on DEC1 & DEC2 lines.
But i am not able to...
Hi,
I would like to include the direct test mode in my default application that runs the BLE stack. Is this possible ? Ideally I am implementing a custom NUS like service...
Hello,
I wish to download my source code to nRF5340 DK board.
I am working on Ubuntu, SEGGER Embedded Studio for ARM Release 5.50d, ncs 1.6.99 version.
After compile...
I'm trying to restrict the policy used to ensure that the AWS FOTA sample is working. The "allow everything" policy that is stated that it can be used for test purposes seems...
SoftDevice: s140_nrf52_7.2.0_softdevice SDK: nRF5_SDK_17.0.2_d674dde Problem: We trying to use the Secure DFU buttonless feature on our custom board. Our custom board has...
Hello,
We are currently using softdevice version 7.0.1 and SDK version 16.0.0. We are having difficulty nailing down a rare hard faulting bug. Very rarely, the device will...
Hi, I'm using Segger Embedded Studio for developing farmware of nRF52840.
and, using
nrf5_SDK_for_Mesh_v4.2.0_src
nRF5_SDK_16.0.0_98a08e2
I would like to use "es_battery_voltage...
i wish to change P0.13 as tx, P0.15 as rx , P0.17 as ctx , P0.20 as rtx
I change in bsp definitions and it worked for uart peripheral example,
I also change pin...
Hello,
The USB connector came apart from the nRF9160 development kit soon after a purchase was made from Symmetry Electronics. Would it be possible to have the board replaced...
