Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am using:
2x Nrf51422 chips on PCA10028
IAR Embedded Workbench IDE - ARM 9.10.2
nRF5_SDK_12.3.0_d7731ad
I need to transfer a 44 byte payload from one board to the...
I think my nrf SDK toolchain manager missed a tool somehow. When I downloaded v1.6.1 (following the instructions on the website) and tried to build my project using
`west...
Hi, I am testing the flash storage of nrf52840 with NVS example from NCS v1.4.2
i have run the example code successfully. from the example code i have changed the
uint8_t...
Hello,
I am trying to create a single static library for SDK, and use it in application and bootloader, for that i have merged sdk_config.h files of application and bootloader...
Hi there,
We are a cycling accessories company (mainly light accessories) and have been using Nordic chips for BLE 1 to 1 connection of our helmet to phone (for configurations...
Hi,
I have added the bettery service to ble_app_buttonless_dfu_pca10040_s132 project successfully.
The sample code is from latest SDK 17.0.2 .
When I do the same set...
Hey Folks,
The new LPUART (doc here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/drivers/uart_nrf_sw_lpuart.html ) is supposed to address the issue of...
Hi, I am testing " Zigbee OTA Upgrade Server Example with image transfer over BLE ", https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v3.2.0%2Fzigbee_example_ota_server...
On the device I have flashed the nRF91 with the latest firmware from here: ncs/nrf/applications/asset_tracker_v2. I have flashed the nRF52 firmware with the most recent firmware...
Dear Sir,
I am working on Bootloader of nRF52840 which I need large space to display some LCD when bootloader startup.
I use Keil compiler, SDK 1702.
In Keil, iROM...
Hi,
I'm planning to develope a set of BLE mesh devices (one control unit which is the coordinator and configurator) and sensor devices (low-power, friend and relay nodes...
Hello,
i need a very sample code for ,open a SPI device ad send , receive a byte.
In particular how open the device tree spi device,
how write a byte
how read a byte...
Excuse me：
1、How many low power modes does NRF have?
2、What is the power consumption in various modes?
3、What is the eDRX power consumption(LTE-M and NB-IOT) and average...
Dear Nordic,
I've integrated a BLE central device with an existing BLE mesh product to create a device that would scan & pair with a monitoring device, collect the data...
