Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi ,
I had done the user guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/ug_matter_configuring.html#ug-matter-configuring , could you please tell...
Somehow it seems the interface MCU of my PCA10040 DK got confused. I cannot use the JLINK to the nRF any more, and the JLINK drive (in Windows 10) does not show up. LD5 stays...
Hi,
1. I want to know the minimum delay time of BLE data transmission
2.How should this time be calculated
Thank you for all your assistance. Kind regards, Peter.Mi...
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello Nordic Devzone,
I am currently attempting to generate 8mhz clock output to a gpio pin on the nrf5340dk. I have found previous posts about utilizing the gpiote, timer...
Dear Members,
How can I find the cause of
<error> app: Fatal error ?
I can't see an error code ?
Is it possible hardware error because voltage surge ? Can capacitor...
When I set NRF_LOG_ENABLED true, the RTT log can be output without any problem, however, the scanning or advertising activity stop immediately.
I found there is something...
Hi,
I am trying to find Get and set the RTC timer api inside Nordic SDK "nCS\v1.6.1\zephyr".
Could you please help me where I can get these api.
Thank You!!
I got up to this stage while trying to evaluate the module...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk_gsg%2FUG%2Fnrf91_DK_gsg%2Fintro.html
There...
Several place refer us to the SoftDevice Release Notes; eg
https://www.nordicsemi.com/eng/nordic/Products/nRF52832/S132-SD-v5/58987
http://infocenter.nordicsemi.com/topic...
Hi,
I have nRF52840 DK with nRFConnect SDK 1.6.99
Compiled and run on nRF52840 boards:
F:\_Develop\ConnectSDK\ncs\zephyr\samples\bluetooth\periodic_adv
F:\_Develop...
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
What does m_ble_observer stand for ? i don't see any explanation in the whole project...
According to the Overview of this sample, the sample supports the provisioning of the IoT device using "Azure IoT Hub Device Provisioning Service (DPS)" to an IoT hub; and...
I am developing firmware for nRF52811 and I can't get UART working.
Sending data over TX works fine, but every time I try to receive something from RX, I get an error. ...
