after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, my device need be ota to update fw by usb in mac os, the chip is nrf52840，and i download the nrfutil-mac ,i execute the dfu in the mac os fail，but in the windowns success...
Hi:
When nrf52 series chips use 32.768KHz crystal oscillator as RTC clock source, the operation error is large at low temperature. Therefore, the following problems need...
I am working with nRF52811 and having a problem with programming and reading flash memory.
I am using J-Link programmer connected with USB.
In nRF Connect Programmer the...
Hello,
I am trying to run the demo thread DFU example by following the docs but without any success. I somehow managed to reach the last step where I have to set DFU server...
Dear Nordic,
could you please suggest what should be done to make USB console & shell options work? What should be checked?
It was quite fine on nCS v1.5.1, and completely...
hi support team，
customer want to setup a timer with 800 us and then 1200 us and then repeatedly without any delay.
for now i use timer to set channel 1 with 800 us cc...
Hi all,
I am using NRF5340 in my custom board. The spims are working well, they are developed by nrfx lib in NRF SDK 1.5.1.
However, after I updated my sdk to 1.6.1, the...
Hello,
I was looking over the board -nRF52 DK- and saw a solder bridge labeled as SB31. But I could not find an information about it in the documentation . Could you please...
Hi All,
I have developed a Bluetooth application with nrf52840, which can be upgraded through our own APP (implementation 'no.nordicemi. Android: DFU: 1.10.3'). However...
Hi All,
I need to do RSA encryption and decryption using nRF52832. I am planning to use mbed TLS library.
Can you please help me to share some example code which can I...
I have encountered some problems when trying to use ENC28j60 ethernet module with nrf52840dongle and hope to get some help from here. Problems:
No internet access on Ipv4...
Hi
I try to run a nRF9160 on a nRF9160DK with lowest power possible.
A wake up from pin and periodically from RTC is required.
In the nRF9160_PS_v2.0.pdf is IMCUON1...
Hello,
We have a Xamarin Forms application, which we use for connecting to nrf52840 device and read/write characteristics. We managed to do it using Plugin.BLE nuget available...
I have difficulties in decoding the nRF9160 GPS output data. I know that nRF9160 reports its GPS data in NMEA GPGGA format, however, I am wondering why the last number which...
