Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi All,
I am trying to make a project for RGB lights using nRF52-DK using NCS.
In these lines of code I am getting the following error -
'DT_N_ALIAS_rgb_pwm_P_ch0_pin...
Hi All,
wondering if anyone else has experienced this. I'm currently developing a program based off of the ble_hids example in SDK17. Currently I'm using the app_timer...
Hi All,
Setup:
SoC: nRF51822
SDK: 11.0.0
Softdevice: S130 2.0.1
I am facing occasional HardFault and It is happening randomly. I need to test device few hours...
Hi Team,
I am trying to perform firmware update of nrf52840DK using MCUBOOT bootloader over UART. I have followed the link: https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello everyone,
How can I use rand() and srand() functions in NCS?
I have already #include <stdlib.h > , but I got this issue:
undefined reference to `srand'
Thanks...
Hi Team,
I am facing the problem while adding static library (.a) file to the segger environment project. If this added successfully then I can easily access the function...
I found that there is no project or example of FTD for nRF52811 both in "openthread/ot-nrf528xx" and "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8"
I want to know that...
Hi,
I bought two of the NRF52840 Dongles to learn and develop smart home compliant applications running on ZigBee protocol. My goal is to create a Smart Home ZigBee hub...
Hello, i would like to interface nrf9160 DK with an rfid reader mfrc522 using SPI. So, i went through the example of spi_master in SDK 8.1.0. It was for nrf51822 and i want...
Hello Nordic support,
I would like to know how can I use the function zb_zdo_mgmt_permit_joining_req() to make the coordinator start the permit to join process forever....
Hi there,
We received your devkits on Friday, 25th of June and started evaluation of the modules this morning (Magnus Pederson and Brian Kim @ Nordic arranged the devkits...
Hi Support,
I have nRF52840 Dongle (PCA10059) on which i am trying to flash thread ncp example as explained here ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fstruct_sdk...
Hey everybody, I am completely new with Nordic devices and tools. Looks like I erased the connectivity bridge application in the nrf52 module at Thingy:91. Now the board is...
Hi,
I am using the nRF9160 to read data from the CCS811 gas sensor, and logs data on LTE Monitor. I am using the BME280 sensor to read temperature and pressure values and...
Hello, I am currently learning to use nRF9160 DK in Guangzhou, China.
It is weird that my China Mobile cellphone SIM card can be used on this DK to connect to Cloud. However...
