after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, The purpose of this is to have a software Power ON/OFF button, when I first start the firmware, it automatically goes OFF. Then after a long press on the button, it should...
I am using nrf52832 controller and interface with MAX30102 sensor. when i tried to read heart rate in nrf connect application , it shows Sensor Contact not supported.
Hi!
I try to set up a unit test environment for my project but I still encounter problems with the runner generation process.
I have the following project structure
...
Hi,
I am trying to have mcuboot in Zephyr to execute the hello world sample (mcuboot\samples\zephyr\hello-world).
I generated the bin for hello world and signed it as...
Hi. I have an urgent issue where after using the JLINK disk programming function on the NRF52-DK, my device is stuck in high current (3ma) debug mode until power is cycled...
I'm sending Data from nRF51822 to nRF24L01. The configuration of the nRF51822 is NRF_RADIO->PREFIX0 = 0x43434343UL; NRF_RADIO->BASE0 = 0x43434343UL; The address of the 24L01...
Dear support team, I would like to simultaneously use logging and CLI via UART in an application running on the NRF52810 with Softdevice S112. In my application, I need to...
Hi
I am having a problem debugging a basic UART code.
I am using Segger-16 for Nordic, and I have an issue with #include "app_uart.h"
I downloaded the nRF_SDK_17.0.2...
Hi,
could some one inform me how to create a bare metal project for nRF5340 (Network Core/Application Code)? The specification gives everything to create an own stack on...
Hi there!
I'm having an issue adding WiFi functionality to my project. I use the nRF9160DK and the nRF Connect SDK v1.5.1 on a Windows10 platform.
To keep it simple i...
I am using nrf52DK board as an observer to test my beacons. I have kept scanning enabled all the time (scanning interval & scanning window same), but the scan_evt_handler...
I want to use the nrf5x to develop the host/gateway of bluetooth mesh, may I ask which model is more suitable, which model currently supports the most mesh nodes?
And which...
Hi Nordic team,
I have successfully developed an application using nrfx (Timer/PPI/SAADC) combo in NCS 1.5.x to be able to sample 2x differential channels very fast.
Similar...
I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I have a device that uses a custom BLE service, And when using nRF Connect on the mobile phone, all...
