Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Dear community,
I need to operate a BM833A as I2C slave and to do so, I performed the following steps:
I modfied my sdk_config.h and set TWIS_ENABLED and NRFX_TWIS_ENABLED...
Hi,
I used nRF Connect for power profiler and programmer for hundreds of times.
But since today, it just keeps on showing white screen.
I tried "Ctrl + R" as well as...
Hi Team,
We are using the NRF52840 SOC for our development purpose and in our application we are planning to port the RTOS.
Could you please suggest us which RTOS is...
HI,
I am using the central_hids project in NCS V1.5.1 on NRF52840 , and now i want to add USB hid into the project, how can i do it?
I have try to do it in nrf_desktop...
Hello,
I've been trying to learn to develop an app based on ZigBee, it's the first time i'm working with nRF hardware and the only things i've done so far was to run some...
Hi,
I am currently trying to embed the ATT_MTU throughput example on two nRF52840 dongles. The main issue I am facing is that after I compile and program the hex files onto...
Hi everyone,
I am working with the nrf52832 Dk boards,
So my question is I want to connect sensors to two nrf52832 boards and want to get their data on a single Android...
Hi.
We use nRF5_SDK_17.0.2_d674dde as central
And phone as peripheral.
Usually system works correctly for a long time.
But sometimes it enter in strange state.
Connections...
Hi
I would like to store data in memory and to be able to read them after. But I don't know how to proceed ! I use IDE segger. Is it possible to store data always in a...
Hi,
I use MQTT_Simple example with AGPS feature;
I add 3 functions, one for init GPS, one for start GPS, and the last for A_GPS request.
I call Init after "MQTT client...
I'm having some difficulties sorting out what support there is for the nRF52832 in ARM's Mbed. Specifically, whether Mbed v6+ uses the SoftDevice or not.
Some things that...
Hi I have recently started to use nrf5340dk for a 'pet' project. I have developed some code for both app and net.
Then I started to note have some trouble on the serial...
Hello world :-)
As there is no Issues section in sdk-nrf I will post my question here. After west update I cannot build my firmware anymore. I am using v2.6.0 Zephyr and...
Hi,
We developed a code using Fanstel nrf52832X BLE using serial UART command to control, receive data and send data.
The softdevice is s132_nrf52_6.1.1_softdevice.hex...
