Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
I am using "pheripheral heartrate" example on SES, but I can not integrate SPI or ADC. How can I add "nrf_spi.h" and "nrf_adc.h" and relative C files on that project...
I'm using an NRF52811 and trying to configure the UARTE for Tx & Rx at 57600 baud but I'm having trouble with the Rx. I think I am dropping bytes and so want to try and exploit...
Hi,
please find attached some patches to improve the code quality of the SDK
1. Make ble_db_discovery_evt_t a const ptr
2. make p_string in ble_nus_c_string_send...
Hello,
i just loaded compilled peripheral_uart project without modification from nrfConnect sdk v1.5.1 to nrf52840 of the nrf9160 dk
and here is the output on uart output...
Hi, I successfully implemented a custom BLE service using this tutorial from Nordic. Also, thanks to a Nordic engineer, I have the QSPI example merged with the ble_app_template...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
Shalom!
In my central nrf52840 board we connect to a TI BLE sensor that has a customer UUID base service and the TI OAD base service both with 128 UUIDs. I succeeded in...
Hi all,
In my project am sending ecg values over ble to android app. During first connection, the values are received and seems to be no problem, but when i disconnect and...
Hello,
I want to increase the number of peers stored in flash. Right now I have FDS_VIRTUAL_PAGES as 3. If I increase this, would I be able what I need? I just need 10 pages...
Hi guys,
I have a problem opening CMSIS Configuration Wizard, but only in Mesh SDK. Because I am working in this SDK, do you maybe know how can I fix this issue. I checked...
Hi, I was testing NCS v1.5.0 and Azure FOTA application and found a bug in the is_update() function
If the current firmware version is shorter than the new one, it may...
Hello, In our current project we are using NRF9160 with NRF52811 as BT device over HCI. Firmware on NRF52811 is just Bluetooth: HCI UART example with pinmux changed to match...
Hi Nordic team, I'm having a custom board and custom application made for that board. Application is based on the zephyr v2.3.0. I decided to move to the NCS because i want...
Hi guys:
a. I use a uart dfu bootloader(loacation: SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart) in 52840 soc...
