Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello
SDK ver 17
DK nRF52 DK
DK is a peripheral connected to many centrals. Every time I connect to a phone I get the messages attached in the picture.. My question...
Hello, support team:)
Currently I am working on SPI communication with LSM6DSOXTR.
CLK, MOSI, SS is working as expected. But there is no MISO signal.
0) All SPI...
Hi,
Just would like to know is it possible to proceed auto pairing by restore the MAC address of host?
The current idea is using direct advertising to speed up the pairing...
Can a provisioner work as a client connect to a server
how do I set on the phone app(iPhone 10s)
in example/light_switch I did not do any change on the example
...
Hi,
I'm in the process of integrating nrf52840 module in HCI over UART to a linux host.
So far I have been able to build the hci_uart in from the samples and bring it...
Dear Members,
How can I share GPIO pin between SPI and I2C peripheral ?
I see SCK_PIN and MISO_PIN for SPI are the same with SCK and SDK on I2C
#define SER_APP_SPIM0_SCK_PIN...
For reference I am using the nRF5 SDK version 17.0.2. I have been comparing the flash_placement.xml files in the <SDK>/config directory and in some of the examples. I have...
Hi. I am looking for simple example of using QDEC for nrf5340. I want to use the Segger Embedded Studio.
Where can I find the example of some guide for HW driver for nrf5340pdk...
i am using nrf52833 development kit here i am using peripheral template as for coding purpose when i merge temperature sensor(SSTS751) code and W25Qxx code in it then the...
I am trying to build the connectivity hex files on an ubuntu build machine for an nrf52840 dongle so I can communicate with another nrf52840 dev board, I followed the instructions...
Hello, my project has 3 different devices (2 sensor and flash memory) on the same SPI bus all with their own CS. I ran across the following question , which has a response...
Hi ,
My environment :
nrf connect sdk
nrf5340 dk
segger studio IDE
verified method 1:
As per nrf5340 product specification document , we can protect the...
Hello,
I was recently trying out some samples with the nRF9160 DK and I had run into some issues when trying to run the nRF Cloud Client Application .
I had flashed...
